Changes for page Zūm Net Device Setup

Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -47,6 +47,8 @@
47	47	** Though saved as a text file, the Device Summary is actually a table of comma separated values
48	48	** Renaming DeviceSummary.txt to DeviceSummary.csv will allow it to be opened and manipulated in common spreadsheet software such as Microsoft Excel or LibreOffice Calc
49	49
	50	+Below is an example of a DeviceSummary.txt and DeviceSummary.csv for a fully-configured job:
	51	+
50	50	Once the Device Summary has been generated, proceed to identifying each ZUMNET-JBOX using the hostname, SN/MAC, or Device Tree View methods described below.
51	51
52	52	===== Identifying by Hostname =====
...	...	@@ -75,10 +75,11 @@
75	75
76	76	===== Identifying through Network Device Tree View =====
77	77
78		-If the electrical contractor has not provided a list of which serial numbers/MAC addresses belong to each installed ZUMNET-JBOX, then it is necessary to connect to each ZUMNET-JBOX individually and identify them through Toolbox. Putting a device into identify will stop any programs running on a processor, and taking a device out of identify mode will restart the program. This starting/stopping of the program can be time consuming when a large number of devices are being identified, so it may be a good idea to run the ##stopprog -p:01## command on the processor prior to identifying devices. Once all the devices are identified, run the ##progreset## command to resume the program.
	80	+If the electrical contractor has not provided a list of which serial numbers/MAC addresses belong to each installed ZUMNET-JBOX and nobody intends to rename each ZUMNET-JBOX using the Crestron Zūm App, then the only way to identify which ZUMNET-JBOX is installed where is to use the Device Tree View tool in Toolbox. This is by far the slowest and most disruptive way to identify devices, so it is only recommended as a last resort.
79	79
80		-* Connect to the lighting network and open Device Discovery Tool in Toolbox
81		-* Note the IP addresses for all of the installed ZUMNET-JBOXs
	82	+Putting a ZUMNET-JBOX into identify mode will make it continuously produce an alarm-clock sound and flash any connected loads. Additionally, putting a device into identify mode will stop any programs running on a processor, and taking a device out of identify mode will restart the program. This starting/stopping of the program can be time consuming when a large number of devices are being identified, so it may be a good idea to suspend the program using the ##stopprog -p:01## command on the processor prior to identifying devices. Once all the devices are identified, run the ##progreset## command to resume the program.
	83	+
	84	+* Generate a Device Summary and note the IP addresses for all installed ZUMNET-JBOXs
82	82	* Connect to the first ZUMNET-JBOX using Network Device Tree View
83	83	* Locate the "ZUMNET-JBOX-xx-xx-LOCAL" device in the list of connected devices
84	84	** The model will vary between 0-10V and DALI JBOXs
...	...	@@ -86,15 +86,17 @@
86	86	* Right click the device and press "Identify This Device..." from the context menu
87	87	* The device will blink any attached fixtures and make an alarm sound
88	88	* Walk around the jobsite until the room/controlled fixtures are located
89		-* Update the SRTakeoff.xlsx with the device serial number, MAC address, and automatically assigned IP address
90		-* Repeat all steps for each ZUMNET-JBOXs until all of the ZUMNET-JBOXs have been identified
	92	+* Edit the Device Summary or SRTakeoff.xlsx so that you remember which JBOX is which
	93	+* Repeat for each ZUMNET-JBOX until all of the ZUMNET-JBOXs have been identified
91	91
	95	+Once you have determined and recorded which ZUMNET-JBOX is which, you may proceed to IP configuration.
	96	+
92	92	==== Assigning Permanent Static IP Addresses and IP-IDs ====
93	93
94	94	Once you have identified which IP address has been assigned to each ZUMNET-JBOX, you can begin configuring them with permanent static IP addresses and the correct IP-ID:
95	95
96	96	* Open Text Console in Toolbox and connect to the first ZUMNET-JBOX
97		-* Run the following commands to configure the ZUMNET-JBOXs IP settings (example is for a **10.0.0.0(% style="color:darkgoldenrod" %)/24(%%)** subnet, with a permanent IP address of (% style="color:blue" %)**10.0.0.80**(%%), an IP-ID of (% style="color:olive" %)**30**(%%), a processor IP address of (% style="color:orange" %)**10.0.0.10**(%%), and a hostname of (% style="color:#800080" %)**ZNET-JBOX-RM-201**(%%))
	102	+* Run the following commands to configure the ZUMNET-JBOXs IP settings (example is for a **10.0.0.0(% style="color:darkgoldenrod" %)/24(%%)** subnet, with a permanent IP address of (% style="color:blue" %)**10.0.0.80**(%%), an IP-ID of (% style="color:olive" %)**30**(%%), a processor IP address of (% style="color:orange" %)**10.0.0.10**(%%), and a hostname of (% style="color:#800080" %)**ZNET-JBOX-RM-201**(%%); the hostname can be skipped if it has already been configured from the Crestron Zūm App)
98	98	** Disable DHCP: ##dhcp off##
99	99	** Set IP address: ##ipa 0 (% style="color:blue" %)**10.0.0.80**(%%)##
100	100	** Set IP subnet mask: ##ipm 0 (% style="color:darkgoldenrod" %)**255.255.255.0**(%%)##