Required Tools and Software

Version 19.1 by Alexander Mott on 2022/06/21 18:03

SHOWRUNNER™ Startups

The SHOWRUNNER™ program has many features to simplify and streamline Crestron lighting control startups, reducing the amount of technical knowledge required and time spent on-site. Even so, there are a number of different software programs and tools required for a successful SHOWRUNNER™ startup. 

"Required" items are absolutely necessary for startup, while "Recommended" items are not strictly necessary but are good to have.

All Startups

Required:
  • Windows Laptop (Windows 10 recommended)
    • Internet access is required to generate and download the SHOWRUNNER™ license on-site
      • Most cellphones can be used as hot spots for this purpose
      • Dedicated hot spot is highly recommended
    • Laptop must have an RJ-45 Ethernet port or a suitable adapter
  • Software:
  • Downloads:
    • Latest SHOWRUNNER™ .puf file
    • Job-specific SHOWRUNNER™ configuration .json file
    • Latest Crestron firmware for installed devices
    • Latest SHOWRUNNER™ UI .puf file (only required for jobs with touchscreens other than TSW-770)
    • SHOWRUNNER™ GLPAC expansion program (only required for jobs with GLPAC controllers)
  • Cables:
    • Cat5/Cat5e/Cat6 Ethernet cable (multiple cables and multiple lengths are recommended)
    • USB-A to USB-B cable (required for most devices; 15' minimum cable length recommended for jobs with GLPACs)
    • USB-A to Mini-B cable (required for RMC3 processors only)
    • USB-A to Micro-B cable (required for CEN-GWEXER, RMC4 processors, and some other devices)
Recommended:
  • A secondary device with internet access (e.g. iPad, second laptop, or cell phone) with remote access software (such as Splashtop)
    • This allows you to "untether" yourself from the lighting network; the laptop stays connected to the lighting network and is able to be remotely accessed via the secondary device
  • Remotes:
  • Hand Tools:
    • Standard Screwdriver (#1 and #2 Phillips, 1/4" and 3/16" Slotted)
    • Precision Screwdriver (2.5mm or 3/32" Slotted; for use with Phoenix Connectors)
    • Wire Stripper (standard Cresnet cable has both 18 AWG and 22 AWG stranded wires)
    • Bright flashlight or laser pointer (for testing photocells)
  • Measurement devices:
    • Low-voltage Multimeter (continuity testing and low voltage DC measurements are frequently required for troubleshooting)
    • Ethernet Network Cable Tester (these are expensive, but useful for verifying Ethernet run lengths and terminations)
  • Software:
    • Chief Integrations Remote Help Tool (download from http://help.chiefintegrations.com/; requires internet access on-site to use)
    • FTP client (such as FileZilla or WinSCP)
    • SSH client (such as PuTTY)
    • File archiver (such as 7-Zip or WinRAR)
    • IP scanning utility (such as Advanced IP Scanner)

Zūm Wired Startups

Zūm Wired startups require all the items listed under "All Startups" plus the following:

Required:
  • Bluetooth-capable Android device with the Crestron Zūm app installed
    • The iOS Crestron Zūm app does not currently support Zūm Wired as of June 2022
    • Officially Android 5.0 is the minimum requirement, but Chief Integrations recommends Android 10.0 or higher
Recommended:

DMX Startups

DMX startups require all the items listed under "All Startups" plus the following:

Required:
Recommended:
  • DMX Tester (e.g. a Swisson XMT-120A)
  • XLR adapters (3-pin male/female, 5-pin male/female, RJ-45, etc.)

DALI Startups

DALI startups require all the items listed under "All Startups" plus the following:

Required:
  • Crestron Toolbox DALI Commissioning Tool (usually included with Crestron Toolbox installation)