Skip to Content
Last modified by Alexander Mott on 2024/06/13 19:47
From version 4.1
edited by Alexander Mott
on 2024/06/13 19:39
Change comment: There is no comment for this version
To version 3.1
edited by Alexander Mott
on 2023/05/12 14:35
Change comment: There is no comment for this version

Summary

Details

Page properties
Title
... ... @@ -1,1 +1,1 @@
1 -sACN and Art-Net Receive (eDMX Receiver)
1 +sACN and Art-Net Receive
Content
... ... @@ -1,32 +1,1 @@
1 -ShowRunnerCLC™ comes standard with a built-in eDMX receiver capable of receiving sACN or Art-Net packets from a third-party DMX controller and mapping those received eDMX values into output levels for ShowRunnerCLC™-controlled hardware. This allows a third-party DMX controller (such as a theatrical control panel) to directly command ShowRunnerCLC™-controlled loads through eDMX. One common use-case for this feature is to allow individuals running a theatrical event to use their temporarily installed DMX console to directly control ShowRunnerCLC™ house lighting as if they were DMX fixtures, without the need to use Crestron keypads or touch screens.
2 -
3 -= Hardware Requirements =
4 -
5 -These are the hardware/networking requirements for integrating a third-party DMX controller with ShowRunnerCLC™'s eDMX receiver:
6 -
7 -* Third-party controller must be capable of sending eDMX commands via sACN or Art-Net
8 -* Third-party controller must be able to send eDMX signals to the lighting control processor
9 -** i.e. third-party controller must be on the same LAN or VLAN as the lighting control processor
10 -* If either of the above cannot be achieved, then a [[DIN-SACN-DMX (Enttec DIN Ethergate 2)>>https://www.crestron.com/Products/Lighting-Environment/Lighting-Fixture-Accessories/Interfaces/DIN-SACN-DMX]] must be added to the ShowRunnerCLC™ controlled hardware
11 -** DIN-SACN-DMX will have traditional DMX connection to the third-party controller and receive ordinary DMX (non-eDMX) signals from the third-party controller
12 -** DIN-SACN-DMX must be on the lighting control LAN/VLAN
13 -
14 -= Information Requirements =
15 -
16 -The following information/coordination must be arranged by the Agent prior to the eDMX receiver being added to the ShowRunnerCLC™ configuration:
17 -
18 -* **(Required)** eDMX type (sACN or Art-Net)
19 -** If traditional DMX is used, then sACN from a DIN-SACN-DMX receiver is assumed
20 -* **(Required)** Universe/Channel to ShowRunnerCLC™ load map
21 -** Agent must coordinate which eDMX channels are used to control each ShowRunnerCLC™ load or load group
22 -** Multiple eDMX receivers can be defined in ShowRunnerCLC™ configuration to allow for different areas to be controlled separately
23 -* //(Optional)// Channel and threshold for enabling or disabling eDMX receiver from the third-party controller
24 -** **Default**: none (eDMX receiver is always active)
25 -* //(Optional)// Add a Global Action to ShowRunnerCLC™ to enable or disable the eDMX receiver?
26 -** **Default**: no global action (eDMX receiver is always active)
27 -* //(Optional)// Restrict the IP address for the eDMX receiver to listen to (i.e., provide the IP address of the third-party controller)?
28 -** **Default**: no restriction (eDMX receiver will obey commands from any IP address)
29 -* //(Optional)// Port for the eDMX receiver to listen on
30 -** **Default**: 5568 (sACN) or 6454 (Art-Net)
31 -
32 -
1 +ShowRunnerCLC™ can receive sACN or Art-Net packets and translate received values to lighting loads, effectively allowing non-DMX, ShowRunner™-controlled loads to be mapped to eDMX channels. One use-case for this feature is to enable control of house lights from a temporarily installed DMX panel in an event space.