Changes for page DMX Input via Pharos

Summary

• Page properties (3 modified, 0 added, 0 removed)

Details

Page properties

Parent

...	...	@@ -1,1 +1,1 @@
1		-SHOWRUNNER™ Integrations Guide.Integration Options.WebHome
	1	+SHOWRUNNER™ User Guide & Wiki.SHOWRUNNER™ Appendix.WebHome

Author

...	...	@@ -1,1 +1,1 @@
1		-XWiki.alexander\.mott@chiefintegrations\.com
	1	+XWiki.mark\.kohlmann@chiefintegrations\.com

Content

...	...	@@ -1,23 +1,15 @@
1		-(% class="box warningmessage" %)
2		-(((
3		-Note: This should only be used if there is no ability to generate an e-DMX (sACN/Art-Net) feed into ShowRunnerCLC™.  [[E-DMX receiver>>doc:SHOWRUNNER™ Integrations Guide.Integration Options.sACN and ArtNet Receive.WebHome]] is much more efficient.
4		-)))
	1	+SHOWRUNNER™ can accept commands from a Pharos' DMX input.  Note: Pharos recommends not using anymore than 50 channels on the DMX input.
5	5
6		-ShowRunnerCLC™ can accept commands from a Pharos' DMX input.  Note: Pharos recommends not using more than 50 channels on the DMX input.  Use as few channels as possible and try not to send fades over DMX into the Pharos.
7		-
8	8	Steps:
9	9
10		-ShowRunnerCLC™
	5	+SHOWRUNNER™
11	11
12		-1. Enable [[UDP Listener>>doc:SHOWRUNNER™ Integrations Guide.Integration Options.UDP Input.WebHome]] in the ShowRunnerCLC™ config:
	7	+1. Enable [[UDP Listener>>doc:SHOWRUNNER™ User Guide & Wiki.SHOWRUNNER™ Appendix.UDP Input.WebHome]] in the SHOWRUNNER™ config:
13	13
14		-(% class="box" %)
15		-(((
16		-## "UdpListener":
17		- {
18		- "ListenPort": 45794
19		- },##
20		-)))
	9	+ "UdpListener":
	10	+ {
	11	+ "ListenPort": 45794
	12	+ },
21	21
22	22	Pharos Config:
23	23
...	...	@@ -25,17 +25,17 @@
25	25	1. Go to Project->Project Features and set DMX In under Trigger to Enabled
26	26	1. Go to Network->Select Controller with DMX Input->Interfaces and set the Serial Port to DMX Input
27	27	1. Triggers
28		-11. Create a trigger on each DMX Input that you wish to send to ShowRunnerCLC™
	20	+11. Create a trigger on each DMX Input that you wish to send to SHOWRUNNER™
29	29	11. Set Trigger Parameters:
30	30	111. Channel: Channel # you wish to capture
31	31	111. Changes in range: Minimum: 0 Maximum: 255
32	32	11. New Action: Output Ethernet
33	33	111. Enable Variables
34		-111. IP/Hostname: IP Address or Hostname of the processor running ShowRunnerCLC™
	26	+111. IP/Hostname: IP Address or Hostname of the processor running SHOWRUNNER™
35	35	111. Port: 45794
36	36	111. Protocol: UDP
37	37	111. String: "GID.SetLevelByByte.<3>\r"
38		-1111. GID is the GlobalID for the load within ShowRunnerCLC™
	30	+1111. GID is the GlobalID for the load within SHOWRUNNER™
39	39	111. Example DMX Channel 41 controlling load with global ID of 32:
40	40	[[image:1597260805025-107.png||height="58" width="693"]]
41	41