*GLS-SIM - XWiki

1

(% class="row" %)

2

(((

3

(% class="col-xs-12 col-sm-8" %)

4

(((

5

(% class="box warningmessage" %)

6

(((

7

Note: GLS-SIM come with two dials labeled "HI" and "LO" which are used for setting the GLS-SIM's network address. These dials should be left at the factory "00" position unless specifically instructed to change them - if these dials are set to anything else then the address for the GLS-SIM cannot be changed via software and is only able to be changed using the dials.

)))

Lorem

See //[[Figure 1>>WebHome||anchor="HFigure1"]]// for details.

13

See //[[Figure 2>>WebHome||anchor="HFigure2"]]// for details.

= Device Wiring =

GLS-SIMs have two distinct sensor ports, allowing for up to two distinct inputs on each GLS-SIM. Inputs can come from any number of devices, including occupancy sensors, photocells, key switches, and contact closures.

18

19

== Occupancy Sensor ==

20

21

All occupancy sensors to be used with a GLS-SIM must be a "non-system" sensor. Cresnet or ZUMLINK sensors should be connected via Cresnet or ZUMLINK instead of the sensor port of a GLS-SIM.

22

23

== Photocell (Daylight Sensor) ==

Lorem

== Key Switch ==

There are two primary kinds of key switches: momentary and maintained. In addition to official Crestron key switches, there are third party manufacturers of key switches and buttons which can be used as inputs for a GLS-SIM.

30

31

=== Crestron Momentary ===

==== ====

=== Crestron Maintained ===

36

37

Note: feedback is not available on maintained key switches, since the feedback status of the switch is apparant from the position of the key.

38

39

=== Other Manufacturers ===

= DIP Switches =

Every GLS-SIM has four DIP switches which can be used to adjust the behavior and function of the two sensor ports on the GLS-SIM. For every DIP switch, the "up" position corresponds to "on", while the "down" position corresponds to "off". Switches 1 and 2 correspond to sensor port 1, while switches 2 and 3 correspond to sensor port 2.

45

46

The table below covers the function of each of the DIP switches and their affect on the GLS-SIM.

47

48

(% class="table-condensed" %)

49

|(% style="width:50px" %)**Port**|(% style="width:92px" %)**DIP Switch**|(% style="width:85px" %)**Setting**|(% style="width:757px" %)**Result**

50

|(% rowspan="4" style="width:50px" %)1|(% rowspan="2" style="width:92px" %)1|(% style="width:85px" %)On (Up)|(% style="width:757px" %)Disables pull-up resistor for port 1

51

|(% style="width:85px" %)Off (Down)|(% style="width:757px" %)Enables pull-up resistor on port 1 (port 1 will output 5V)

52

|(% rowspan="2" style="width:92px" %)2|(% style="width:85px" %)On (Up)|(% style="width:757px" %)Normal polarity (high input reads as "true")

53

|(% style="width:85px" %)Off (Down)|(% style="width:757px" %)Inverted polarity (high input reads as "false")

54

|(% rowspan="4" style="width:50px" %)2|(% rowspan="2" style="width:92px" %)3|(% style="width:85px" %)On (Up)|(% style="width:757px" %)Disables pull-up resistor for port 2

55

|(% style="width:85px" %)Off (Down)|(% style="width:757px" %)Enables pull-up resistor on port 2 (port 2 will output 5V)

56

|(% rowspan="2" style="width:92px" %)4|(% style="width:85px" %)On (Up)|(% style="width:757px" %)Normal polarity (high input reads as "true")

57

|(% style="width:85px" %)Off (Down)|(% style="width:757px" %)Inverted polarity (high input reads as "false")

58

59

== Occupancy Sensor ==

60

61

Lorem