Skip to Content

Wiki source code of GLS-SIM

Version 4.1 by Alexander Mott on 2022/10/17 19:10
Show last authors
1 (% class="row" %)
2 (((
3 (% class="col-xs-12 col-sm-8" %)
4 (((
5 (% class="box warningmessage" %)
6 (((
7 Note: GLS-SIM come with two dials labeled "HI" and "LO" which are used for setting the GLS-SIM's network address. These dials should be left at the factory "00" position unless specifically instructed to change them - if these dials are set to anything else then the address for the GLS-SIM cannot be changed via software and is only able to be changed using the dials.
8 )))
9
10 Lorem
11
12 See //[[Figure 1>>WebHome||anchor="HFigure1"]]// for details.
13 See //[[Figure 2>>WebHome||anchor="HFigure2"]]// for details.
14
15 = Device Wiring =
16
17 GLS-SIMs have
18
19 == Occupancy Sensor ==
20
21 Lorem
22
23 == Photocell (Daylight Sensor) ==
24
25 Lorem
26
27 == Key Switch ==
28
29 Lorem
30
31 === Momentary ===
32
33 === Maintained ===
34
35 = DIP Switches =
36
37 Every GLS-SIM has four DIP switches which can be used to adjust the behavior and function of the two sensor ports on the GLS-SIM. For every DIP switch, the "up" position corresponds to "on", while the "down" position corresponds to "off". Switches 1 and 2 correspond to sensor port 1, while switches 2 and 3 correspond to sensor port 2.
38
39 The table below covers the function of each of the DIP switches and their affect on the GLS-SIM.
40
41 (% class="table-condensed" %)
42 |(% style="width:50px" %)**Port**|(% style="width:92px" %)**DIP Switch**|(% style="width:85px" %)**Setting**|(% style="width:757px" %)**Result**
43 |(% rowspan="4" style="width:50px" %)1|(% rowspan="2" style="width:92px" %)1|(% style="width:85px" %)On (Up)|(% style="width:757px" %)Disables pull-up resistor for port 1
44 |(% style="width:85px" %)Off (Down)|(% style="width:757px" %)Enables pull-up resistor on port 1 (port 1 will output 5V)
45 |(% rowspan="2" style="width:92px" %)2|(% style="width:85px" %)On (Up)|(% style="width:757px" %)Normal polarity (high input reads as "true")
46 |(% style="width:85px" %)Off (Down)|(% style="width:757px" %)Inverted polarity (high input reads as "false")
47 |(% rowspan="4" style="width:50px" %)2|(% rowspan="2" style="width:92px" %)3|(% style="width:85px" %)On (Up)|(% style="width:757px" %)Disables pull-up resistor for port 2
48 |(% style="width:85px" %)Off (Down)|(% style="width:757px" %)Enables pull-up resistor on port 2 (port 2 will output 5V)
49 |(% rowspan="2" style="width:92px" %)4|(% style="width:85px" %)On (Up)|(% style="width:757px" %)Normal polarity (high input reads as "true")
50 |(% style="width:85px" %)Off (Down)|(% style="width:757px" %)Inverted polarity (high input reads as "false")
51
52 == Occupancy Sensor ==
53
54 Lorem
55
56 == Photocell (Daylight Sensor) ==
57
58 Lorem
59
60 == Key Switch ==
61
62 Lorem
63
64 = Troubleshooting =
65
66
67 )))
68
69
70 (% class="col-xs-12 col-sm-4" %)
71 (((
72 {{box title="**CONTENTS**"}}
73 {{toc/}}
74 {{/box}}
75
76 (% class="wikigeneratedid" id="HFigure1" %)
77 (((
78 [[image:Templates.Article.Template.WebHome@image1.jpg]]
79 //Figure 1: [[Sea>>https://commons.wikimedia.org/wiki/File:Isle_of_Icacos_II.jpg]]//
80 )))
81
82 (% class="wikigeneratedid" id="HFigure2" %)
83 (((
84 [[image:Templates.Article.Template.WebHome@image2.jpg]]
85 //Figure 2: [[Waves>>https://commons.wikimedia.org/wiki/File:Culebra_-_Playa_de_Flamenco.jpg]]//
86 )))
87 )))
88 )))