Skip to Content

Changes for page *GLS-SIM

Last modified by Alexander Mott on 2024/01/05 18:22
From version 5.1
edited by Alexander Mott
on 2022/10/17 20:46
Change comment: There is no comment for this version
To version 2.2
edited by Alexander Mott
on 2022/10/17 14:45
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -2,11 +2,6 @@
2 2  (((
3 3  (% class="col-xs-12 col-sm-8" %)
4 4  (((
5 -(% class="box warningmessage" %)
6 -(((
7 -Note: GLS-SIM come with two dials labeled "HI" and "LO" which are used for setting the GLS-SIM's network address. These dials should be left at the factory "00" position unless specifically instructed to change them - if these dials are set to anything else then the address for the GLS-SIM cannot be changed via software and is only able to be changed using the dials.
8 -)))
9 -
10 10  Lorem
11 11  
12 12  See //[[Figure 1>>WebHome||anchor="HFigure1"]]// for details.
... ... @@ -14,11 +14,11 @@
14 14  
15 15  = Device Wiring =
16 16  
17 -GLS-SIMs have two distinct sensor ports, allowing for up to two distinct inputs on each GLS-SIM. Inputs can come from any number of devices, including occupancy sensors, photocells, key switches, and contact closures.
12 +Lorem
18 18  
19 19  == Occupancy Sensor ==
20 20  
21 -All occupancy sensors to be used with a GLS-SIM must be a "non-system" sensor. Cresnet or ZUMLINK sensors should be connected via Cresnet or ZUMLINK instead of the sensor port of a GLS-SIM.
16 +Lorem
22 22  
23 23  == Photocell (Daylight Sensor) ==
24 24  
... ... @@ -26,25 +26,18 @@
26 26  
27 27  == Key Switch ==
28 28  
29 -There are two primary kinds of key switches: momentary and maintained. In addition to official Crestron key switches, there are third party manufacturers of key switches and buttons which can be used as inputs for a GLS-SIM.
24 +Lorem
30 30  
31 -=== Crestron Momentary ===
26 +=== Momentary ===
32 32  
33 -==== ====
28 +=== Maintained ===
34 34  
35 -=== Crestron Maintained ===
30 += DIP Switch Settings =
36 36  
37 -Note: feedback is not available on maintained key switches, since the feedback status of the switch is apparant from the position of the key.
32 +Every GLS-SIM has four DIP switches which can be used to adjust the behavior and function of the two sensor ports on the GLS-SIM. For every DIP switch, the "up" position corresponds to "on", while the "down" position corresponds to "off". Switches 1 and 2 correspond to sensor port 1, while switches 2 and 3 correspond to sensor port 2.
38 38  
39 -=== Other Manufacturers ===
34 +The table below covers the function of each of the DIP switches and their affect on the
40 40  
41 -
42 -= DIP Switches =
43 -
44 -Every GLS-SIM has four DIP switches which can be used to adjust the behavior and function of the two sensor ports on the GLS-SIM. For every DIP switch, the "up" position corresponds to "on", while the "down" position corresponds to "off". Switches 1 and 2 correspond to sensor port 1, while switches 2 and 3 correspond to sensor port 2.
45 -
46 -The table below covers the function of each of the DIP switches and their affect on the GLS-SIM.
47 -
48 48  (% class="table-condensed" %)
49 49  |(% style="width:50px" %)**Port**|(% style="width:92px" %)**DIP Switch**|(% style="width:85px" %)**Setting**|(% style="width:757px" %)**Result**
50 50  |(% rowspan="4" style="width:50px" %)1|(% rowspan="2" style="width:92px" %)1|(% style="width:85px" %)On (Up)|(% style="width:757px" %)Disables pull-up resistor for port 1
... ... @@ -69,8 +69,6 @@
69 69  Lorem
70 70  
71 71  = Troubleshooting =
72 -
73 -
74 74  )))
75 75  
76 76