Skip to Content

Changes for page *GLS-SIM

Last modified by Alexander Mott on 2024/01/05 18:22
From version 4.1
edited by Alexander Mott
on 2022/10/17 19:10
Change comment: There is no comment for this version
To version 2.1
edited by Alexander Mott
on 2022/10/17 14:25
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -2,11 +2,6 @@
2 2  (((
3 3  (% class="col-xs-12 col-sm-8" %)
4 4  (((
5 -(% class="box warningmessage" %)
6 -(((
7 -Note: GLS-SIM come with two dials labeled "HI" and "LO" which are used for setting the GLS-SIM's network address. These dials should be left at the factory "00" position unless specifically instructed to change them - if these dials are set to anything else then the address for the GLS-SIM cannot be changed via software and is only able to be changed using the dials.
8 -)))
9 -
10 10  Lorem
11 11  
12 12  See //[[Figure 1>>WebHome||anchor="HFigure1"]]// for details.
... ... @@ -14,7 +14,7 @@
14 14  
15 15  = Device Wiring =
16 16  
17 -GLS-SIMs have
12 +Lorem
18 18  
19 19  == Occupancy Sensor ==
20 20  
... ... @@ -24,7 +24,7 @@
24 24  
25 25  Lorem
26 26  
27 -== Key Switch ==
22 +== Key Switches ==
28 28  
29 29  Lorem
30 30  
... ... @@ -32,38 +32,19 @@
32 32  
33 33  === Maintained ===
34 34  
35 -= DIP Switches =
30 += Dipswitch Settings =
36 36  
37 -Every GLS-SIM has four DIP switches which can be used to adjust the behavior and function of the two sensor ports on the GLS-SIM. For every DIP switch, the "up" position corresponds to "on", while the "down" position corresponds to "off". Switches 1 and 2 correspond to sensor port 1, while switches 2 and 3 correspond to sensor port 2.
38 -
39 -The table below covers the function of each of the DIP switches and their affect on the GLS-SIM.
40 -
41 -(% class="table-condensed" %)
42 -|(% style="width:50px" %)**Port**|(% style="width:92px" %)**DIP Switch**|(% style="width:85px" %)**Setting**|(% style="width:757px" %)**Result**
43 -|(% rowspan="4" style="width:50px" %)1|(% rowspan="2" style="width:92px" %)1|(% style="width:85px" %)On (Up)|(% style="width:757px" %)Disables pull-up resistor for port 1
44 -|(% style="width:85px" %)Off (Down)|(% style="width:757px" %)Enables pull-up resistor on port 1 (port 1 will output 5V)
45 -|(% rowspan="2" style="width:92px" %)2|(% style="width:85px" %)On (Up)|(% style="width:757px" %)Normal polarity (high input reads as "true")
46 -|(% style="width:85px" %)Off (Down)|(% style="width:757px" %)Inverted polarity (high input reads as "false")
47 -|(% rowspan="4" style="width:50px" %)2|(% rowspan="2" style="width:92px" %)3|(% style="width:85px" %)On (Up)|(% style="width:757px" %)Disables pull-up resistor for port 2
48 -|(% style="width:85px" %)Off (Down)|(% style="width:757px" %)Enables pull-up resistor on port 2 (port 2 will output 5V)
49 -|(% rowspan="2" style="width:92px" %)4|(% style="width:85px" %)On (Up)|(% style="width:757px" %)Normal polarity (high input reads as "true")
50 -|(% style="width:85px" %)Off (Down)|(% style="width:757px" %)Inverted polarity (high input reads as "false")
51 -
52 -== Occupancy Sensor ==
53 -
54 54  Lorem
55 55  
56 -== Photocell (Daylight Sensor) ==
34 +== Sub-paragraph ==
57 57  
58 58  Lorem
59 59  
60 -== Key Switch ==
38 +== Sub-paragraph ==
61 61  
62 62  Lorem
63 63  
64 64  = Troubleshooting =
65 -
66 -
67 67  )))
68 68  
69 69