Skip to Content

Changes for page Ethernet Wiring Overview

Last modified by Alexander Mott on 2024/01/05 18:55
From version 5.1
edited by Alexander Mott
on 2021/12/20 23:45
Change comment: Uploaded new attachment "T568B pin-out.png", version {1}
To version 3.2
edited by Alexander Mott
on 2021/12/20 23:22
Change comment: There is no comment for this version

Summary

Details

Page properties
Title
... ... @@ -1,1 +1,1 @@
1 -Ethernet
1 +*Ethernet
Content
... ... @@ -1,39 +5,31 @@
1 -{{box title="**Contents**"}}
2 -{{toc/}}
3 -{{/box}}
4 -
5 5  (% class="row" %)
6 6  (((
7 7  (% class="col-xs-12 col-sm-8" %)
8 8  (((
9 -= Ethernet Wiring =
5 += Ethernet Wiring Standards =
10 10  
11 -Ethernet is used for various devices within a Crestron Lighting Control system, including connecting a lighting control processor to the lighting network, connecting Zūm Net devices to the lighting network, connecting TSW touch-screen interfaces to the lighting network, and connecting the lighting network itself to a building network (building LAN).
7 +Ethernet is used to connect
12 12  
13 13  == Cabling ==
14 14  
15 -All cable should be Category 5e or greater (including Category 6 and Category 6a).
11 +All Ethernet cable should be Category 5e, Category 6, or Category 6a.
16 16  
17 -The maximum length of any single ethernet run is 100 meters (328 feet). Runs longer than this will require a powered ethernet switch (such as a CEN-SW-POE-5) to be installed midway through the run to enable proper communication.
18 -
19 19  == Terminations ==
20 20  
21 21  Cresnet Ethernet devices require the use of RJ-45 connectors.
22 22  
23 -While either T568A or T568B termination pin-out are acceptable as long as they are used consistently, it is **recommended to use the T568B pin-out for all terminations.** By keeping to one standard, it is easier to stay consistent and prevent errors where the two sides of a single cable are not terminated to the same standard.
17 +While either T568A or T568B termination pin-out are acceptable, it is **recommended to use the T568B pin-out for all terminations.** By keeping to one standard, it is easier to stay consistent and prevent errors where the two sides of a single cable are not terminated to the same standard.
24 24  
25 25  See// Figure 1 //for the T568-B pin-out.
26 -
27 -When making RJ-45 terminations, take care that the wires are in the correct order and pushed all the way to the end of the connector. A crimping tool with sharp blades that have not been dulled with use also helps in making good terminations.
28 -
29 -== Testing ==
30 -
31 -
32 32  )))
33 33  
34 34  
35 35  (% class="col-xs-12 col-sm-4" %)
36 36  (((
25 +{{box title="**Contents**"}}
26 +{{toc/}}
27 +{{/box}}
28 +
37 37  [[image:Templates.Article.Template.WebHome@image1.jpg]]
38 38  //Figure 1: [[Sea>>https://commons.wikimedia.org/wiki/File:Isle_of_Icacos_II.jpg]]//
39 39  )))
T568B pin-out.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.alexander\.mott@chiefintegrations\.com
Size
... ... @@ -1,1 +1,0 @@
1 -92.9 KB
Content