Skip to Content
Last modified by Alexander Mott on 2024/01/05 18:55
From version 24.2
edited by Alexander Mott
on 2022/09/19 18:40
Change comment: Update document after refactoring.
To version 26.1
edited by Scott Kohlmann
on 2023/04/21 14:17
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.alexander\.mott@chiefintegrations\.com
1 +XWiki.scott\.kohlmann@chiefintegrations\.com
Content
... ... @@ -12,7 +12,7 @@
12 12  1. Disconnect the 0-10V wiring to the fixtures
13 13  1. Connect a multimeter to the 0-10V dimming output of the module
14 14  1. Measure the 0-10V output at various brightness levels
15 -1*. If the system has been partially or fully commissioned, it may be possible to use the showrunner™ UI to adjust the brightness
15 +1*. If the system has been partially or fully commissioned, it may be possible to use the ShowRunnerCLC™ UI to adjust the brightness
16 16  1*. Alternatively, some modules have physical buttons that can be used to adjust their brightness:
17 17  1**. Press the button to toggle the output on or off. A small LED light on the module will indicate current output on/off status.
18 18  1**. Once the output is on, press and hold the button to cycle dim the output (first press and hold will lower the output, subsequent press and holds will toggle between raising and lowering the output)
... ... @@ -43,7 +43,7 @@
43 43  1. Identify the module and output that should be controlling the fixtures
44 44  1. Disconnect the 0-10V wiring to the fixtures
45 45  1. Toggle the module output on and off to verify it is switching the correct zone
46 -1*. If the system has been partially or fully commissioned, it may be possible to use the showrunner™ UI to toggle the module output
46 +1*. If the system has been partially or fully commissioned, it may be possible to use the ShowRunnerCLC™ UI to toggle the module output
47 47  1*. Alternatively, some modules have physical buttons that can be used to toggle the output:
48 48  1**. Press the button to toggle the output on or off. A small LED light on the module will indicate current output on/off status.
49 49  1**. Once the output is on, press and hold the button to cycle dim the output (first press and hold will lower the output, subsequent press and holds will toggle between raising and lowering the output)
... ... @@ -101,7 +101,7 @@
101 101  
102 102  On the front of the Zūm JBOX-16A-LV (outside the junction box) are two or three LEDs next to a black button. The LED labeled "TEST" will be green if the output is hot. The black button can be used to toggle the output on or off, and holding the button will cycle dim the 0-10V output.
103 103  
104 -See //[[Figure 1>>SHOWRUNNER™ Setup Guide.Troubleshooting Guide.Wiring and Hardware.0-10V Dimming Troubleshooting.WebHome||anchor="HFigure1"]]// for details.
104 +See //[[Figure 1>>WebHome||anchor="HFigure1"]]// for details.
105 105  
106 106  == CLX-2DIMFLV8 and CLX-2DIMFLV8-277 ==
107 107  
... ... @@ -111,7 +111,7 @@
111 111  
112 112  On the front of 0-10V CLX modules are eight buttons corresponding to each of the eight outputs. Next to each button is a red LED indicating the current load status. The LED will be lit if the output is on. To the right of the LED is the 0-10V output for each channel, which can be easily unplugged for troubleshooting. The buttons can be used to toggle each channel independently, and holding the button will cycle dim the 0-10V output for that channel.
113 113  
114 -See //[[Figure 2>>SHOWRUNNER™ Setup Guide.Troubleshooting Guide.Wiring and Hardware.0-10V Dimming Troubleshooting.WebHome||anchor="HFigure2"]]// for details.
114 +See //[[Figure 2>>WebHome||anchor="HFigure2"]]// for details.
115 115  
116 116  == GL-EXP-DIMFLV-CN ==
117 117  
... ... @@ -143,7 +143,7 @@
143 143  
144 144  The 0-10V outputs are located on the top right of the module. A small screwdriver is required to disconnect the dimming to the fixtures.
145 145  
146 -See //[[Figure 3>>SHOWRUNNER™ Setup Guide.Troubleshooting Guide.Wiring and Hardware.0-10V Dimming Troubleshooting.WebHome||anchor="HFigure3"]]// for details.
146 +See //[[Figure 3>>WebHome||anchor="HFigure3"]]// for details.
147 147  
148 148  == GLXP-DIMFLV8 (Discontinued) ==
149 149  
... ... @@ -155,7 +155,7 @@
155 155  
156 156  The 0-10V outputs are split into the eight negative outputs and the eight positive outputs on the lower left of the module. A small screwdriver is required to disconnect the dimming to the fixtures.
157 157  
158 -See //[[Figure 4>>SHOWRUNNER™ Setup Guide.Troubleshooting Guide.Wiring and Hardware.0-10V Dimming Troubleshooting.WebHome||anchor="HFigure4"]]// for details.
158 +See //[[Figure 4>>WebHome||anchor="HFigure4"]]// for details.
159 159  
160 160  = Real World 0-10V Data =
161 161