Skip to Content
Last modified by Alexander Mott on 2024/01/05 18:55
From version 19.1
edited by Alexander Mott
on 2022/09/17 00:34
Change comment: There is no comment for this version
To version 32.1
edited by Alexander Mott
on 2024/01/05 18:55
Change comment: Renamed back-links.

Summary

Details

Page properties
Parent
... ... @@ -1,1 +1,1 @@
1 -SHOWRUNNER™ Setup Guide.WebHome
1 +SHOWRUNNER™ Setup Guide.Troubleshooting Guide.Troubleshooting.WebHome
Content
... ... @@ -1,13 +5,7 @@
1 -{{box title="**CONTENTS**"}}
2 -{{toc/}}
3 -{{/box}}
4 -
5 5  (% class="row" %)
6 6  (((
7 7  (% class="col-xs-12 col-sm-8" %)
8 8  (((
9 -= Overview =
10 -
11 11  0-10V dimming is one of the most common dimming methods for LED fixtures. It utilizes a 0-10VDC signal from the lighting controller to the fixture power supply or driver in order to control the brightness of the fixtures. This 0-10VDC signal is typically carried over a shielded pair of gray (negative) and violet (positive) wires. In the event that 0-10V dimming fixtures are exhibiting unexpected dimming behavior, an easy place to begin troubleshooting is at the lighting control module.
12 12  
13 13  = Verifying Module Output =
... ... @@ -18,7 +18,7 @@
18 18  1. Disconnect the 0-10V wiring to the fixtures
19 19  1. Connect a multimeter to the 0-10V dimming output of the module
20 20  1. Measure the 0-10V output at various brightness levels
21 -1*. If the system has been partially or fully commissioned, it may be possible to use the showrunner™ UI to adjust the brightness
15 +1*. If the system has been partially or fully commissioned, it may be possible to use the ShowRunnerCLC™ UI to adjust the brightness
22 22  1*. Alternatively, some modules have physical buttons that can be used to adjust their brightness:
23 23  1**. Press the button to toggle the output on or off. A small LED light on the module will indicate current output on/off status.
24 24  1**. Once the output is on, press and hold the button to cycle dim the output (first press and hold will lower the output, subsequent press and holds will toggle between raising and lowering the output)
... ... @@ -49,7 +49,7 @@
49 49  1. Identify the module and output that should be controlling the fixtures
50 50  1. Disconnect the 0-10V wiring to the fixtures
51 51  1. Toggle the module output on and off to verify it is switching the correct zone
52 -1*. If the system has been partially or fully commissioned, it may be possible to use the showrunner™ UI to toggle the module output
46 +1*. If the system has been partially or fully commissioned, it may be possible to use the ShowRunnerCLC™ UI to toggle the module output
53 53  1*. Alternatively, some modules have physical buttons that can be used to toggle the output:
54 54  1**. Press the button to toggle the output on or off. A small LED light on the module will indicate current output on/off status.
55 55  1**. Once the output is on, press and hold the button to cycle dim the output (first press and hold will lower the output, subsequent press and holds will toggle between raising and lowering the output)
... ... @@ -179,9 +179,12 @@
179 179  
180 180  )))
181 181  
182 -
183 183  (% class="col-xs-12 col-sm-4" %)
184 184  (((
178 +{{box title="**CONTENTS**"}}
179 +{{toc/}}
180 +{{/box}}
181 +
185 185  (% class="wikigeneratedid" id="HFigure1" %)
186 186  (((
187 187  [[[[image:zumlink.png]]>>attach:zumlink.png]]