Last modified by Mark Kohlmann on 2024/04/05 19:48
Show last authors
1 (% class="box warningmessage" %)
2 (((
3 Buttons 5 and 6 presently cannot be exposed to ShowRunnerCLC™ and will only work locally.  ZUMMESH-KPAV type keypads are not supported with this approach and require an AVBRIDGE.
4 )))
5
6 ShowRunnerCLC™ supports receiving button presses from ZUMMESH-KP* keypads.  Overriding buttons is done on a per button basis.
7
8 Requirements:
9
10 * JBOX w/ NETBRIDGE
11 * ZUMMESH Firmware v1.07.016 or newer
12 ** NETBRIDGE firmware v1.013.0021
13 ** ZUM-KPBATT firmware v0010000113
14 ** ZUM-JBOX-SIM firmware v0010000067
15 * NETBRIDGE defined in ShowRunner as a load controller
16 * ZUMMESH-KP or ZUMMESH-KPBATT (Excludes ZUMMESH-KPAV series keypads are not supported due to lack of firmware support)
17 * ShowRunner™ 3.004 or newer
18
19 Keypads have 6 buttons, 1 through 4 can be exported individually, 5 and 6 are supported by ShowRunner but not Crestron:
20 [[image:ZUMMESH-KP Buttons.png]]
21
22
23 JBOX-SIM is supported. O is button 1, V is button 2, and D is button 3.
24
25
26 Keypad definition in ShowRunner config:
27
28 ##//**DeviceConnectionId**//## is the KeypadId used to uniquely identify the ZUMMESH-KP.  This must be between 1 and 255.
29 ##//**DeviceHostId**// ##is the IP-ID of the RF Gateway that owns the NETBRIDGE
30 ##//**DeviceHostBranch**// ##is the RF-ID of the NETBRIDGE on the gateway
31 ##//**Model**// ##may be the actual keypad model excluding the color and finish.  Example ZUMMESH-KP10GBATT-GRY-S is "ZUMMESH-KP10GBATT".  "ZUMMESH-KP" or "ZUMMESH-KPBATT" may also be used.
32
33 ## "7": {
34 "AreaId": 2,
35 "LinkedAreaIds": null,
36 "Id": 7,
37 "Name": "Zummesh KP",
38 **~ "//DeviceConnectionId//": "1",**
39 **~ "//DeviceHostId//": "B0",**
40 **~ "//DeviceHostBranch//": 5,**
41 "SerialNumber": "",
42 "DisableOff": false,
43 "DisallowDisable": false,
44 "FlipRaiseLower": false,
45 "MasterRaiseButtonIndex": 0,
46 "MasterLowerButtonIndex": 0,
47 "HoldTime": 0.5,
48 "DoubleTapTime": 0.5,
49 "//**Model**//": "ZUMMESH-KPBATT",
50 "Enabled": true,
51 "KeypadType": "A",
52 "ControllerIds": [],
53 "DirectLoadIds": null,
54 "Actions": null,
55 }##
56
57 ==== Automatic Setup: ====
58
59 This method will automatically enable all buttons to report to ShowRunnerCLC™
60
61 * Console to ShowRunnerCLC™
62 * Obtain the keypad address by querying the devices on the NETBRIDGE:
63 ##sr zummesh show devices [Gateway IP-ID in hex] [NETBRIDGE RF-ID in hex]##
64 Example: ##sr zummesh show devices B0 1A##
65 [[image:1626996842264-632.png]]
66 * Setup the keypad buttons that will report to ShowRunnerCLC™:
67 ##sr zummesh keypad custom buttons [Gateway IP-ID] [NETBRIDGE RF-ID] [Keypad Address] [Keypad Id] [List of Buttons to Override Local Logic, comma/dash separated list]##
68 Example: ##sr zummesh keypad custom buttons B0 1A 52E5 1 1-6##
69 [[image:1626997279912-938.png]]
70
71 ==== Manual Setup: ====
72
73 Use this setup method if you wish to assign specific ShowRunnerCLC™ button IDs to ZUMMESH-KPs or selective send buttons to ShowRunnerCLC™
74
75 * Connect to RF Gateway console
76 * ##RFRCON [NETBRIDGE RF-ID] DISPLAYDEVICES## to obtain the Addr of the Keypad
77 [[image:1626997350133-604.png]]
78 * Calculate Button IDs:
79 Keypad IDs are 1 to 255
80 Button Numbers are 1 to 6
81 Tap Action is 0
82 Hold Action is 1
83 Release Action is 2
84 ExportId = (Keypad ID << 8) + (Button Number << 4) + ButtonAction
85 Example for keypad id of 2 button 2 w/ hold action
86 ##(2 << 8) + (2 << 4) + 1 = 545 or 221h##
87 Example for keypad id of 128 button 5 w/ tap action
88 ##(128 << 8) + (5 << 4) + 0 = 32848 or 8050h##
89 * Send command per button to enable reporting:
90 ##rfrcon [NETBRIDGE-RFID] setbuttfunc [KEYPAD ADDRESS] [ButtonNumber] 22 [Tap-ExportID in hex] [Hold-ExportID in hex] [Release-ExportID in hex]
91 rfrcon 03 setbuttfunc 52E5 2 22 220 221 222##
92 [[image:1626997728072-241.png]]

Navigation