Skip to Content
Version 5.2 by Mark Kohlmann on 2021/07/22 23:42
Show last authors
1 ShowRunner™ supports receiving button presses from ZUMMESH-KP* keypads.  AV keypads have not been verified for support yet, this only applies to regular lighting keypads.  Overriding buttons is done on per button basis.
2
3 Requirements:
4
5 * JBOX w/ NETBRIDGE
6 * ZUMMESH Firmware v1.07.016 or newer
7 * NETBRIDGE defined in ShowRunner as a load controller
8 * ZUMMESH-KP or ZUMMESH-KPBATT (Excludes ZUMMESH-KPAV series keypads)
9 * ShowRunner™ 3.004 or newer
10
11 Keypads have 6 buttons, each can be exported individually:
12 [[image:ZUMMESH-KP Buttons.png]]
13
14 Keypad definition in ShowRunner config:
15
16 ##//**DeviceConnectionId**//## is the KeypadId used to uniquely identify the ZUMMESH-KP.  This must be between 1 and 255.
17 ##//**DeviceHostId**// ##is the IP-ID of the RF Gateway that owns the NETBRIDGE
18 ##//**DeviceHostBranch**// ##is the RF-ID of the NETBRIDGE on the gateway
19 ##//**Model**// ##may be the actual keypad model excluding the color and finish.  Example ZUMMESH-KP10GBATT-GRY-S is "ZUMMESH-KP10GBATT".  "ZUMMESH-KP" or "ZUMMESH-KPBATT" may also be used.
20
21 ## "7": {
22 "AreaId": 2,
23 "LinkedAreaIds": null,
24 "Id": 7,
25 "Name": "Zummesh KP",
26 **~ "//DeviceConnectionId//": "1",**
27 **~ "//DeviceHostId//": "B0",**
28 **~ "//DeviceHostBranch//": 5,**
29 "SerialNumber": "",
30 "DisableOff": false,
31 "DisallowDisable": false,
32 "FlipRaiseLower": false,
33 "MasterRaiseButtonIndex": 0,
34 "MasterLowerButtonIndex": 0,
35 "HoldTime": 0.5,
36 "DoubleTapTime": 0.5,
37 "//**Model**//": "ZUMMESH-KPBATT",
38 "Enabled": true,
39 "KeypadType": "A",
40 "ControllerIds": [],
41 "DirectLoadIds": null,
42 "Actions": null,
43 }##
44
45 ==== Automatic Setup: ====
46
47 * Console to ShowRunner
48 * Obtain the keypad address by querying the devices on the NETBRIDGE:
49 ##sr zummesh show devices [Gateway IP-ID in hex] [NETBRIDGE RF-ID in hex]##
50 Example: ##sr zummesh show devices B0 1A##
51 [[image:1626996842264-632.png]]
52 * Setup the keypad buttons that will report to ShowRunner™:
53 ##sr zummesh keypad custom buttons [Gateway IP-ID] [NETBRIDGE RF-ID] [Keypad Address] [Keypad Id] [List of Buttons to Override Local Logic, comma/dash separated list]##
54 Example: sr zummesh keypad custom buttons B0 1A 52E5 1 1-6
55 [[image:1626997279912-938.png]]
56
57 ==== Manual Setup: ====
58
59 * Connect to RF Gateway console
60 * RFRCON [NETBRIDGE RF-ID] DISPLAYDEVICES
61 [[image:1626997350133-604.png]]
62 *