Skip to Content
Last modified by Austin Weygandt on 2025/04/18 15:47
From version 8.1
edited by Mark Kohlmann
on 2021/07/23 03:30
Change comment: There is no comment for this version
To version 12.1
edited by Mark Kohlmann
on 2024/04/05 19:46
Change comment: There is no comment for this version

Summary

Details

Page properties
Parent
... ... @@ -1,1 +1,1 @@
1 -SHOWRUNNER™ User Guide & Wiki.Troubleshooting.WebHome
1 +SHOWRUNNER™ Setup Guide.Troubleshooting Guide.Advanced Tools.WebHome
Content
... ... @@ -1,21 +1,28 @@
1 1  (% class="box warningmessage" %)
2 2  (((
3 -Buttons 5 and 6 presently cannot be exposed to ShowRunner and will only work locally.  ZUMMESH-KPAV type keypads are not supported with this approach and require an AVBRIDGE.
3 +Buttons 5 and 6 presently cannot be exposed to ShowRunnerCLC™ and will only work locally.  ZUMMESH-KPAV type keypads are not supported with this approach and require an AVBRIDGE.
4 4  )))
5 5  
6 -ShowRunner™ supports receiving button presses from ZUMMESH-KP* keypads.  Overriding buttons is done on a per button basis.
6 +ShowRunnerCLC™ supports receiving button presses from ZUMMESH-KP* keypads.  Overriding buttons is done on a per button basis.
7 7  
8 8  Requirements:
9 9  
10 10  * JBOX w/ NETBRIDGE
11 11  * ZUMMESH Firmware v1.07.016 or newer
12 +** NETBRIDGE firmware v1.013.0021
13 +** ZUM-KPBATT firmware v0010000113
14 +** ZUM-JBOX-SIM firmware v0010000067
12 12  * NETBRIDGE defined in ShowRunner as a load controller
13 -* ZUMMESH-KP or ZUMMESH-KPBATT (Excludes ZUMMESH-KPAV series keypads pending verification of support)
16 +* ZUMMESH-KP or ZUMMESH-KPBATT (Excludes ZUMMESH-KPAV series keypads are not supported due to lack of firmware support)
14 14  * ShowRunner™ 3.004 or newer
15 15  
16 16  Keypads have 6 buttons, 1 through 4 can be exported individually, 5 and 6 are supported by ShowRunner but not Crestron:
17 17  [[image:ZUMMESH-KP Buttons.png]]
18 18  
22 +
23 +JBOX-SIM is supported. O is button 1, V is button 2, and P is button 3.
24 +
25 +
19 19  Keypad definition in ShowRunner config:
20 20  
21 21  ##//**DeviceConnectionId**//## is the KeypadId used to uniquely identify the ZUMMESH-KP.  This must be between 1 and 255.
... ... @@ -49,14 +49,14 @@
49 49  
50 50  ==== Automatic Setup: ====
51 51  
52 -This method will automatically enable all buttons to report to ShowRunner™
59 +This method will automatically enable all buttons to report to ShowRunnerCLC™
53 53  
54 -* Console to ShowRunner
61 +* Console to ShowRunnerCLC™
55 55  * Obtain the keypad address by querying the devices on the NETBRIDGE:
56 56  ##sr zummesh show devices [Gateway IP-ID in hex] [NETBRIDGE RF-ID in hex]##
57 57  Example: ##sr zummesh show devices B0 1A##
58 58  [[image:1626996842264-632.png]]
59 -* Setup the keypad buttons that will report to ShowRunner™:
66 +* Setup the keypad buttons that will report to ShowRunnerCLC™:
60 60  ##sr zummesh keypad custom buttons [Gateway IP-ID] [NETBRIDGE RF-ID] [Keypad Address] [Keypad Id] [List of Buttons to Override Local Logic, comma/dash separated list]##
61 61  Example: ##sr zummesh keypad custom buttons B0 1A 52E5 1 1-6##
62 62  [[image:1626997279912-938.png]]
... ... @@ -63,7 +63,7 @@
63 63  
64 64  ==== Manual Setup: ====
65 65  
66 -Use this setup method if you wish to assign specific ShowRunner™ button IDs to ZUMMESH-KPs or selective send buttons to ShowRunner™
73 +Use this setup method if you wish to assign specific ShowRunnerCLC™ button IDs to ZUMMESH-KPs or selective send buttons to ShowRunnerCLC™
67 67  
68 68  * Connect to RF Gateway console
69 69  * ##RFRCON [NETBRIDGE RF-ID] DISPLAYDEVICES## to obtain the Addr of the Keypad