Skip to Content
Last modified by Austin Weygandt on 2025/04/18 15:47
From version 5.2
edited by Mark Kohlmann
on 2021/07/22 23:42
Change comment: There is no comment for this version
To version 10.2
edited by Mark Kohlmann
on 2022/09/19 17:02
Change comment: Updated parent field.

Summary

Details

Page properties
Parent
... ... @@ -1,1 +1,1 @@
1 -SHOWRUNNER™ User Guide & Wiki.Troubleshooting.WebHome
1 +xwiki:SHOWRUNNER™ Setup Guide.Troubleshooting Guide.Software and Programming.Troubleshooting.WebHome
Content
... ... @@ -1,14 +1,21 @@
1 -ShowRunner™ supports receiving button presses from ZUMMESH-KP* keypads.  AV keypads have not been verified for support yet, this only applies to regular lighting keypads.  Overriding buttons is done on per button basis.
1 +(% class="box warningmessage" %)
2 +(((
3 +Buttons 5 and 6 presently cannot be exposed to ShowRunner and will only work locally.  ZUMMESH-KPAV type keypads are not supported with this approach and require an AVBRIDGE.
4 +)))
2 2  
6 +ShowRunner™ supports receiving button presses from ZUMMESH-KP* keypads.  Overriding buttons is done on a per button basis.
7 +
3 3  Requirements:
4 4  
5 5  * JBOX w/ NETBRIDGE
6 6  * ZUMMESH Firmware v1.07.016 or newer
12 +** NETBRIDGE firmware v1.013.0021
13 +** ZUM-KPBATT firmware v0010000113
7 7  * NETBRIDGE defined in ShowRunner as a load controller
8 -* ZUMMESH-KP or ZUMMESH-KPBATT (Excludes ZUMMESH-KPAV series keypads)
15 +* ZUMMESH-KP or ZUMMESH-KPBATT (Excludes ZUMMESH-KPAV series keypads are not supported due to lack of firmware support)
9 9  * ShowRunner™ 3.004 or newer
10 10  
11 -Keypads have 6 buttons, each can be exported individually:
18 +Keypads have 6 buttons, 1 through 4 can be exported individually, 5 and 6 are supported by ShowRunner but not Crestron:
12 12  [[image:ZUMMESH-KP Buttons.png]]
13 13  
14 14  Keypad definition in ShowRunner config:
... ... @@ -44,6 +44,8 @@
44 44  
45 45  ==== Automatic Setup: ====
46 46  
54 +This method will automatically enable all buttons to report to ShowRunner™
55 +
47 47  * Console to ShowRunner
48 48  * Obtain the keypad address by querying the devices on the NETBRIDGE:
49 49  ##sr zummesh show devices [Gateway IP-ID in hex] [NETBRIDGE RF-ID in hex]##
... ... @@ -51,12 +51,28 @@
51 51  [[image:1626996842264-632.png]]
52 52  * Setup the keypad buttons that will report to ShowRunner™:
53 53  ##sr zummesh keypad custom buttons [Gateway IP-ID] [NETBRIDGE RF-ID] [Keypad Address] [Keypad Id] [List of Buttons to Override Local Logic, comma/dash separated list]##
54 -Example: sr zummesh keypad custom buttons B0 1A 52E5 1 1-6
63 +Example: ##sr zummesh keypad custom buttons B0 1A 52E5 1 1-6##
55 55  [[image:1626997279912-938.png]]
56 56  
57 57  ==== Manual Setup: ====
58 58  
68 +Use this setup method if you wish to assign specific ShowRunner™ button IDs to ZUMMESH-KPs or selective send buttons to ShowRunner™
69 +
59 59  * Connect to RF Gateway console
60 -* RFRCON [NETBRIDGE RF-ID] DISPLAYDEVICES
71 +* ##RFRCON [NETBRIDGE RF-ID] DISPLAYDEVICES## to obtain the Addr of the Keypad
61 61  [[image:1626997350133-604.png]]
62 -*
73 +* Calculate Button IDs:
74 +Keypad IDs are 1 to 255
75 +Button Numbers are 1 to 6
76 +Tap Action is 0
77 +Hold Action is 1
78 +Release Action is 2
79 +ExportId = (Keypad ID << 8) + (Button Number << 4) + ButtonAction
80 +Example for keypad id of 2 button 2 w/ hold action
81 +##(2 << 8) + (2 << 4) + 1 = 545 or 221h##
82 +Example for keypad id of 128 button 5 w/ tap action
83 +##(128 << 8) + (5 << 4) + 0 = 32848 or 8050h##
84 +* Send command per button to enable reporting:
85 +##rfrcon [NETBRIDGE-RFID] setbuttfunc [KEYPAD ADDRESS] [ButtonNumber] 22 [Tap-ExportID in hex] [Hold-ExportID in hex] [Release-ExportID in hex]
86 +rfrcon 03 setbuttfunc 52E5 2 22 220 221 222##
87 +[[image:1626997728072-241.png]]
1626997728072-241.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.mark\.kohlmann@chiefintegrations\.com
Size
... ... @@ -1,0 +1,1 @@
1 +5.7 KB
Content