Skip to Content
Last modified by Austin Weygandt on 2025/04/18 15:47
From version 14.1
edited by Austin Weygandt
on 2025/04/18 15:47
Change comment: There is no comment for this version
To version 5.2
edited by Mark Kohlmann
on 2021/07/22 23:42
Change comment: There is no comment for this version

Summary

Details

Page properties
Parent
... ... @@ -1,1 +1,1 @@
1 -SHOWRUNNER™ Setup Guide.Troubleshooting Guide.Advanced Tools.WebHome
1 +SHOWRUNNER™ User Guide & Wiki.Troubleshooting.WebHome
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.austin\.weygandt@chiefintegrations\.com
1 +XWiki.mark\.kohlmann@chiefintegrations\.com
Content
... ... @@ -1,37 +1,16 @@
1 -(% class="box warningmessage" %)
2 -(((
3 -Buttons 5 and 6 presently cannot be exposed to ShowRunnerCLC™ and will only work locally.  ZUMMESH-KPAV type keypads are not supported with this approach and require an AVBRIDGE.
4 -)))
1 +ShowRunner™ supports receiving button presses from ZUMMESH-KP* keypads.  AV keypads have not been verified for support yet, this only applies to regular lighting keypads.  Overriding buttons is done on per button basis.
5 5  
6 -{{error}}
7 - FIRMWARE REQUIREMENTS:
8 -
9 -* ZUMMESH Firmware v1.07.016 or newer
10 -** NETBRIDGE firmware v1.013.0021
11 -** ZUM-KPBATT firmware v1.000.0113
12 -** ZUM-JBOX-SIM firmware v1.000.067
13 -{{/error}}
14 -
15 -ShowRunnerCLC™ supports receiving button presses from ZUMMESH-KP* keypads.  Overriding buttons is done on a per button basis.
16 -
17 17  Requirements:
18 18  
19 19  * JBOX w/ NETBRIDGE
20 20  * ZUMMESH Firmware v1.07.016 or newer
21 -** NETBRIDGE firmware v1.013.0021
22 -** ZUM-KPBATT firmware v1.000.0113
23 -** ZUM-JBOX-SIM firmware v1.000.067
24 24  * NETBRIDGE defined in ShowRunner as a load controller
25 -* ZUMMESH-KP or ZUMMESH-KPBATT (Excludes ZUMMESH-KPAV series keypads are not supported due to lack of firmware support)
8 +* ZUMMESH-KP or ZUMMESH-KPBATT (Excludes ZUMMESH-KPAV series keypads)
26 26  * ShowRunner™ 3.004 or newer
27 27  
28 -Keypads have 6 buttons, 1 through 4 can be exported individually, 5 and 6 are supported by ShowRunner but not Crestron:
11 +Keypads have 6 buttons, each can be exported individually:
29 29  [[image:ZUMMESH-KP Buttons.png]]
30 30  
31 -
32 -JBOX-SIM is supported. O is button 1, V is button 2, and D is button 3.
33 -
34 -
35 35  Keypad definition in ShowRunner config:
36 36  
37 37  ##//**DeviceConnectionId**//## is the KeypadId used to uniquely identify the ZUMMESH-KP.  This must be between 1 and 255.
... ... @@ -65,37 +65,19 @@
65 65  
66 66  ==== Automatic Setup: ====
67 67  
68 -This method will automatically enable all buttons to report to ShowRunnerCLC™
69 -
70 -* Console to ShowRunnerCLC™
47 +* Console to ShowRunner
71 71  * Obtain the keypad address by querying the devices on the NETBRIDGE:
72 72  ##sr zummesh show devices [Gateway IP-ID in hex] [NETBRIDGE RF-ID in hex]##
73 73  Example: ##sr zummesh show devices B0 1A##
74 74  [[image:1626996842264-632.png]]
75 -* Setup the keypad buttons that will report to ShowRunnerCLC™:
52 +* Setup the keypad buttons that will report to ShowRunner™:
76 76  ##sr zummesh keypad custom buttons [Gateway IP-ID] [NETBRIDGE RF-ID] [Keypad Address] [Keypad Id] [List of Buttons to Override Local Logic, comma/dash separated list]##
77 -Example: ##sr zummesh keypad custom buttons B0 1A 52E5 1 1-6##
54 +Example: sr zummesh keypad custom buttons B0 1A 52E5 1 1-6
78 78  [[image:1626997279912-938.png]]
79 79  
80 80  ==== Manual Setup: ====
81 81  
82 -Use this setup method if you wish to assign specific ShowRunnerCLC™ button IDs to ZUMMESH-KPs or selective send buttons to ShowRunnerCLC™
83 -
84 84  * Connect to RF Gateway console
85 -* ##RFRCON [NETBRIDGE RF-ID] DISPLAYDEVICES## to obtain the Addr of the Keypad
60 +* RFRCON [NETBRIDGE RF-ID] DISPLAYDEVICES
86 86  [[image:1626997350133-604.png]]
87 -* Calculate Button IDs:
88 -Keypad IDs are 1 to 255
89 -Button Numbers are 1 to 6
90 -Tap Action is 0
91 -Hold Action is 1
92 -Release Action is 2
93 -ExportId = (Keypad ID << 8) + (Button Number << 4) + ButtonAction
94 -Example for keypad id of 2 button 2 w/ hold action
95 -##(2 << 8) + (2 << 4) + 1 = 545 or 221h##
96 -Example for keypad id of 128 button 5 w/ tap action
97 -##(128 << 8) + (5 << 4) + 0 = 32848 or 8050h##
98 -* Send command per button to enable reporting:
99 -##rfrcon [NETBRIDGE-RFID] setbuttfunc [KEYPAD ADDRESS] [ButtonNumber] 22 [Tap-ExportID in hex] [Hold-ExportID in hex] [Release-ExportID in hex]
100 -rfrcon 03 setbuttfunc 52E5 2 22 220 221 222##
101 -[[image:1626997728072-241.png]]
62 +*
1626997728072-241.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.mark\.kohlmann@chiefintegrations\.com
Size
... ... @@ -1,1 +1,0 @@
1 -5.7 KB
Content