Skip to Content
Last modified by Austin Weygandt on 2025/04/18 15:47
From version 14.1
edited by Austin Weygandt
on 2025/04/18 15:47
Change comment: There is no comment for this version
To version 10.1
edited by Mark Kohlmann
on 2021/08/20 22:19
Change comment: There is no comment for this version

Summary

Details

Page properties
Parent
... ... @@ -1,1 +1,1 @@
1 -SHOWRUNNER™ Setup Guide.Troubleshooting Guide.Advanced Tools.WebHome
1 +SHOWRUNNER™ User Guide & Wiki.Troubleshooting.WebHome
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.austin\.weygandt@chiefintegrations\.com
1 +XWiki.mark\.kohlmann@chiefintegrations\.com
Content
... ... @@ -1,26 +1,16 @@
1 1  (% class="box warningmessage" %)
2 2  (((
3 -Buttons 5 and 6 presently cannot be exposed to ShowRunnerCLC™ and will only work locally.  ZUMMESH-KPAV type keypads are not supported with this approach and require an AVBRIDGE.
3 +Buttons 5 and 6 presently cannot be exposed to ShowRunner and will only work locally.  ZUMMESH-KPAV type keypads are not supported with this approach and require an AVBRIDGE.
4 4  )))
5 5  
6 -{{error}}
7 - FIRMWARE REQUIREMENTS:
6 +ShowRunner™ supports receiving button presses from ZUMMESH-KP* keypads.  Overriding buttons is done on a per button basis.
8 8  
9 -* ZUMMESH Firmware v1.07.016 or newer
10 -** NETBRIDGE firmware v1.013.0021
11 -** ZUM-KPBATT firmware v1.000.0113
12 -** ZUM-JBOX-SIM firmware v1.000.067
13 -{{/error}}
14 -
15 -ShowRunnerCLC™ supports receiving button presses from ZUMMESH-KP* keypads.  Overriding buttons is done on a per button basis.
16 -
17 17  Requirements:
18 18  
19 19  * JBOX w/ NETBRIDGE
20 20  * ZUMMESH Firmware v1.07.016 or newer
21 21  ** NETBRIDGE firmware v1.013.0021
22 -** ZUM-KPBATT firmware v1.000.0113
23 -** ZUM-JBOX-SIM firmware v1.000.067
13 +** ZUM-KPBATT firmware v0010000113
24 24  * NETBRIDGE defined in ShowRunner as a load controller
25 25  * ZUMMESH-KP or ZUMMESH-KPBATT (Excludes ZUMMESH-KPAV series keypads are not supported due to lack of firmware support)
26 26  * ShowRunner™ 3.004 or newer
... ... @@ -28,10 +28,6 @@
28 28  Keypads have 6 buttons, 1 through 4 can be exported individually, 5 and 6 are supported by ShowRunner but not Crestron:
29 29  [[image:ZUMMESH-KP Buttons.png]]
30 30  
31 -
32 -JBOX-SIM is supported. O is button 1, V is button 2, and D is button 3.
33 -
34 -
35 35  Keypad definition in ShowRunner config:
36 36  
37 37  ##//**DeviceConnectionId**//## is the KeypadId used to uniquely identify the ZUMMESH-KP.  This must be between 1 and 255.
... ... @@ -65,14 +65,14 @@
65 65  
66 66  ==== Automatic Setup: ====
67 67  
68 -This method will automatically enable all buttons to report to ShowRunnerCLC™
54 +This method will automatically enable all buttons to report to ShowRunner™
69 69  
70 -* Console to ShowRunnerCLC™
56 +* Console to ShowRunner
71 71  * Obtain the keypad address by querying the devices on the NETBRIDGE:
72 72  ##sr zummesh show devices [Gateway IP-ID in hex] [NETBRIDGE RF-ID in hex]##
73 73  Example: ##sr zummesh show devices B0 1A##
74 74  [[image:1626996842264-632.png]]
75 -* Setup the keypad buttons that will report to ShowRunnerCLC™:
61 +* Setup the keypad buttons that will report to ShowRunner™:
76 76  ##sr zummesh keypad custom buttons [Gateway IP-ID] [NETBRIDGE RF-ID] [Keypad Address] [Keypad Id] [List of Buttons to Override Local Logic, comma/dash separated list]##
77 77  Example: ##sr zummesh keypad custom buttons B0 1A 52E5 1 1-6##
78 78  [[image:1626997279912-938.png]]
... ... @@ -79,7 +79,7 @@
79 79  
80 80  ==== Manual Setup: ====
81 81  
82 -Use this setup method if you wish to assign specific ShowRunnerCLC™ button IDs to ZUMMESH-KPs or selective send buttons to ShowRunnerCLC™
68 +Use this setup method if you wish to assign specific ShowRunner™ button IDs to ZUMMESH-KPs or selective send buttons to ShowRunner™
83 83  
84 84  * Connect to RF Gateway console
85 85  * ##RFRCON [NETBRIDGE RF-ID] DISPLAYDEVICES## to obtain the Addr of the Keypad