Skip to Content
Last modified by Austin Weygandt on 2025/04/18 15:47
From version 12.1
edited by Mark Kohlmann
on 2024/04/05 19:46
Change comment: There is no comment for this version
To version 10.1
edited by Mark Kohlmann
on 2021/08/20 22:19
Change comment: There is no comment for this version

Summary

Details

Page properties
Parent
... ... @@ -1,1 +1,1 @@
1 -SHOWRUNNER™ Setup Guide.Troubleshooting Guide.Advanced Tools.WebHome
1 +SHOWRUNNER™ User Guide & Wiki.Troubleshooting.WebHome
Content
... ... @@ -1,9 +1,9 @@
1 1  (% class="box warningmessage" %)
2 2  (((
3 -Buttons 5 and 6 presently cannot be exposed to ShowRunnerCLC™ and will only work locally.  ZUMMESH-KPAV type keypads are not supported with this approach and require an AVBRIDGE.
3 +Buttons 5 and 6 presently cannot be exposed to ShowRunner and will only work locally.  ZUMMESH-KPAV type keypads are not supported with this approach and require an AVBRIDGE.
4 4  )))
5 5  
6 -ShowRunnerCLC™ supports receiving button presses from ZUMMESH-KP* keypads.  Overriding buttons is done on a per button basis.
6 +ShowRunner™ supports receiving button presses from ZUMMESH-KP* keypads.  Overriding buttons is done on a per button basis.
7 7  
8 8  Requirements:
9 9  
... ... @@ -11,7 +11,6 @@
11 11  * ZUMMESH Firmware v1.07.016 or newer
12 12  ** NETBRIDGE firmware v1.013.0021
13 13  ** ZUM-KPBATT firmware v0010000113
14 -** ZUM-JBOX-SIM firmware v0010000067
15 15  * NETBRIDGE defined in ShowRunner as a load controller
16 16  * ZUMMESH-KP or ZUMMESH-KPBATT (Excludes ZUMMESH-KPAV series keypads are not supported due to lack of firmware support)
17 17  * ShowRunner™ 3.004 or newer
... ... @@ -19,10 +19,6 @@
19 19  Keypads have 6 buttons, 1 through 4 can be exported individually, 5 and 6 are supported by ShowRunner but not Crestron:
20 20  [[image:ZUMMESH-KP Buttons.png]]
21 21  
22 -
23 -JBOX-SIM is supported. O is button 1, V is button 2, and P is button 3.
24 -
25 -
26 26  Keypad definition in ShowRunner config:
27 27  
28 28  ##//**DeviceConnectionId**//## is the KeypadId used to uniquely identify the ZUMMESH-KP.  This must be between 1 and 255.
... ... @@ -56,14 +56,14 @@
56 56  
57 57  ==== Automatic Setup: ====
58 58  
59 -This method will automatically enable all buttons to report to ShowRunnerCLC™
54 +This method will automatically enable all buttons to report to ShowRunner™
60 60  
61 -* Console to ShowRunnerCLC™
56 +* Console to ShowRunner
62 62  * Obtain the keypad address by querying the devices on the NETBRIDGE:
63 63  ##sr zummesh show devices [Gateway IP-ID in hex] [NETBRIDGE RF-ID in hex]##
64 64  Example: ##sr zummesh show devices B0 1A##
65 65  [[image:1626996842264-632.png]]
66 -* Setup the keypad buttons that will report to ShowRunnerCLC™:
61 +* Setup the keypad buttons that will report to ShowRunner™:
67 67  ##sr zummesh keypad custom buttons [Gateway IP-ID] [NETBRIDGE RF-ID] [Keypad Address] [Keypad Id] [List of Buttons to Override Local Logic, comma/dash separated list]##
68 68  Example: ##sr zummesh keypad custom buttons B0 1A 52E5 1 1-6##
69 69  [[image:1626997279912-938.png]]
... ... @@ -70,7 +70,7 @@
70 70  
71 71  ==== Manual Setup: ====
72 72  
73 -Use this setup method if you wish to assign specific ShowRunnerCLC™ button IDs to ZUMMESH-KPs or selective send buttons to ShowRunnerCLC™
68 +Use this setup method if you wish to assign specific ShowRunner™ button IDs to ZUMMESH-KPs or selective send buttons to ShowRunner™
74 74  
75 75  * Connect to RF Gateway console
76 76  * ##RFRCON [NETBRIDGE RF-ID] DISPLAYDEVICES## to obtain the Addr of the Keypad