Skip to Content
Last modified by Austin Weygandt on 2025/04/18 15:47
From version 10.2
edited by Mark Kohlmann
on 2022/09/19 17:02
Change comment: Updated parent field.
To version 6.1
edited by Mark Kohlmann
on 2021/07/22 23:48
Change comment: Uploaded new attachment "1626997728072-241.png", version {1}

Summary

Details

Page properties
Parent
... ... @@ -1,1 +1,1 @@
1 -xwiki:SHOWRUNNER™ Setup Guide.Troubleshooting Guide.Software and Programming.Troubleshooting.WebHome
1 +SHOWRUNNER™ User Guide & Wiki.Troubleshooting.WebHome
Content
... ... @@ -1,21 +1,14 @@
1 -(% class="box warningmessage" %)
2 -(((
3 -Buttons 5 and 6 presently cannot be exposed to ShowRunner and will only work locally.  ZUMMESH-KPAV type keypads are not supported with this approach and require an AVBRIDGE.
4 -)))
1 +ShowRunner™ supports receiving button presses from ZUMMESH-KP* keypads.  AV keypads have not been verified for support yet, this only applies to regular lighting keypads.  Overriding buttons is done on per button basis.
5 5  
6 -ShowRunner™ supports receiving button presses from ZUMMESH-KP* keypads.  Overriding buttons is done on a per button basis.
7 -
8 8  Requirements:
9 9  
10 10  * JBOX w/ NETBRIDGE
11 11  * ZUMMESH Firmware v1.07.016 or newer
12 -** NETBRIDGE firmware v1.013.0021
13 -** ZUM-KPBATT firmware v0010000113
14 14  * NETBRIDGE defined in ShowRunner as a load controller
15 -* ZUMMESH-KP or ZUMMESH-KPBATT (Excludes ZUMMESH-KPAV series keypads are not supported due to lack of firmware support)
8 +* ZUMMESH-KP or ZUMMESH-KPBATT (Excludes ZUMMESH-KPAV series keypads)
16 16  * ShowRunner™ 3.004 or newer
17 17  
18 -Keypads have 6 buttons, 1 through 4 can be exported individually, 5 and 6 are supported by ShowRunner but not Crestron:
11 +Keypads have 6 buttons, each can be exported individually:
19 19  [[image:ZUMMESH-KP Buttons.png]]
20 20  
21 21  Keypad definition in ShowRunner config:
... ... @@ -51,8 +51,6 @@
51 51  
52 52  ==== Automatic Setup: ====
53 53  
54 -This method will automatically enable all buttons to report to ShowRunner™
55 -
56 56  * Console to ShowRunner
57 57  * Obtain the keypad address by querying the devices on the NETBRIDGE:
58 58  ##sr zummesh show devices [Gateway IP-ID in hex] [NETBRIDGE RF-ID in hex]##
... ... @@ -60,28 +60,12 @@
60 60  [[image:1626996842264-632.png]]
61 61  * Setup the keypad buttons that will report to ShowRunner™:
62 62  ##sr zummesh keypad custom buttons [Gateway IP-ID] [NETBRIDGE RF-ID] [Keypad Address] [Keypad Id] [List of Buttons to Override Local Logic, comma/dash separated list]##
63 -Example: ##sr zummesh keypad custom buttons B0 1A 52E5 1 1-6##
54 +Example: sr zummesh keypad custom buttons B0 1A 52E5 1 1-6
64 64  [[image:1626997279912-938.png]]
65 65  
66 66  ==== Manual Setup: ====
67 67  
68 -Use this setup method if you wish to assign specific ShowRunner™ button IDs to ZUMMESH-KPs or selective send buttons to ShowRunner™
69 -
70 70  * Connect to RF Gateway console
71 -* ##RFRCON [NETBRIDGE RF-ID] DISPLAYDEVICES## to obtain the Addr of the Keypad
60 +* RFRCON [NETBRIDGE RF-ID] DISPLAYDEVICES
72 72  [[image:1626997350133-604.png]]
73 -* Calculate Button IDs:
74 -Keypad IDs are 1 to 255
75 -Button Numbers are 1 to 6
76 -Tap Action is 0
77 -Hold Action is 1
78 -Release Action is 2
79 -ExportId = (Keypad ID << 8) + (Button Number << 4) + ButtonAction
80 -Example for keypad id of 2 button 2 w/ hold action
81 -##(2 << 8) + (2 << 4) + 1 = 545 or 221h##
82 -Example for keypad id of 128 button 5 w/ tap action
83 -##(128 << 8) + (5 << 4) + 0 = 32848 or 8050h##
84 -* Send command per button to enable reporting:
85 -##rfrcon [NETBRIDGE-RFID] setbuttfunc [KEYPAD ADDRESS] [ButtonNumber] 22 [Tap-ExportID in hex] [Hold-ExportID in hex] [Release-ExportID in hex]
86 -rfrcon 03 setbuttfunc 52E5 2 22 220 221 222##
87 -[[image:1626997728072-241.png]]
62 +*