Wiki source code of Zummesh Dynamic White/CCT
Version 15.1 by Mark Kohlmann on 2026/01/08 20:56
Hide last authors
| author | version | line-number | content |
|---|---|---|---|
 |
11.1 | 1 | {{warning}} |
| 2 | Caveats: | ||
| 3 | |||
| 4 | * Only intensity/CCT fixtures are supported. This will not work with warm/cool fixtures. | ||
| |
12.1 | 5 | * NETBRIDGE must be attached to the ZUMMESH-JBOX-DALI. Only 1 ZUMMESH-JBOX-DALI is supported per room. Use Zum Wired or DIN-DALI-2/DIN-DLI if more capabilities are needed. |
| 6 | * Supports up to 8 CCT channels, DALI Groups 2,4,6,8,10,12,14,16 on the Zum app (0 based - 1,3,5,7,9,11,13,15 for ShowRunner/console purposes) | ||
| |
11.1 | 7 | * Zum Scene must have the CCT channel set to 255 to accept input from ShowRunner. Values of 0-254 will be sent directly to the group as fixed colors. |
| 8 | * Setup must be done from the gateway console | ||
| |
13.1 | 9 | * **Loads must be manually changed to BusIndex 3 in the ShowRunner config or added from the UI with BusIndex 3. Normally DALI loads are BusIndex 2.** |
| |
11.1 | 10 | {{/warning}} |
| 11 | |||
| |
13.1 | 12 | Zum wireless supports dynamic white using DALI Groups 2,4,6,8,10,12,14,16 (1,3,5,7,9,11,13,15 for ShowRunner/console purposes). Setup must be performed manually on the NETBRIDGE. Once done, ShowRunner can use the CCT channels to provide CCT data to the fixtures. Input from ShowRunnerCLC™ requires setting the scene recall for the CCT group to 255. Any value of 0-254 will be sent to the CCT channel directly and the input from ShowRunnerCLC™ will be ignored. |
| |
1.1 | 13 | |
| |
2.2 | 14 | ==== Typical Setup for up to 6 zones, 5 fixture types: ==== |
| |
1.3 | 15 | |
| |
8.1 | 16 | (% border="1" style="width:600px" %) |
| |
1.3 | 17 | |=DALI Group|=Name|=Fixture Type|=Control Type |
| 18 | |0|Downlights, Main|F0|Intensity | ||
| |
7.1 | 19 | |1|Downlights, Main/Screen CCT|F0|Color |
| 20 | |2|Accent Lights|F1a|Intensity | ||
| 21 | |3|Accent Lights CCT|F1a|Color | ||
| 22 | |4|Spot Lights|F3|Intensity | ||
| 23 | |5|Spot Lights CCT|F3|Color | ||
| 24 | |6|Troffers|F4c|Intensity | ||
| 25 | |7|Troffers CCT|F4c|Color | ||
| 26 | |8|Linear|F9|Intensity | ||
| 27 | |9|Linear|F9|Color | ||
| 28 | |10|Downlights @ Screen|F0|Intensity | ||
| 29 | |11|-|-|Color | ||
| 30 | |12|-|-|Intensity | ||
| |
1.5 | 31 | |13|-|-|Color |
| |
7.1 | 32 | |14|-|-|Intensity |
| |
1.5 | 33 | |15|-|-|Color |
| |
1.3 | 34 | |
| |
1.1 | 35 | ==== Setup Steps: ==== |
| 36 | |||
| |
15.1 | 37 | |
| 38 | If your DALI groups are already commissioned and you need to specify the groups for color (Examples shown for group 7): | ||
| 39 | |||
| 40 | 1. Modify DALI Group to color, only needed if step 2 was not done. If step 2 was performed skip this step. | ||
| 41 | ##Command: //rfrcon <**NetbridgeID**> DALIGROUPSETTWRITE <**GroupID**> 14 <**GroupType**>// | ||
| 42 | **GroupID: **0 to 15 | ||
| 43 | **GroupType:** 0=Intensity, 1=Color | ||
| 44 | Example: (NETBRIDGE RF-ID 1A): //rfrcon 1A DALIGROUPSETTWRITE 7 14 1//## | ||
| 45 | 1. Set Scene settings for Color Support. Enables or uses a fixed value for color temperature on color groups. This must be done for all scenes that will be used. | ||
| 46 | ##Command: rfrcon <**NetbridgeID**> DALIGROUPCOMMAND 4 <**GroupID**> <**SceneID**> <**SceneLevel**> <**Action**> <**FadeTime**> | ||
| 47 | **GroupID**: 0 to 15 (odd for color) | ||
| 48 | **SceneID**: Scene number (1 to 16) | ||
| 49 | **SceneLevel**: 255 for ShowRunner control, 0-254 for fixed scene level | ||
| 50 | **Action**: 0=Remove Scene, 1=Add Scene | ||
| 51 | **FadeTime**: Fade time in 1/10th of a second | ||
| 52 | Example (NETBRIDGE RF-ID 1A): //rfrcon 1A DALIGROUPCOMMAND 4 7 1 255 1 10// | ||
| 53 | Example (NETBRIDGE RF-ID 1A): //rfrcon 1A DALIGROUPCOMMAND 4 7 2 255 1 10//## | ||
| 54 | |||
| 55 | |||
| 56 | If Starting from scratch without having been commissioned in the Zum App (Examples shown for group 7): | ||
| 57 | |||
| |
13.1 | 58 | 1. ((( |
| 59 | Address all DALI drivers attached to the JBOX. This can be done via the gateway console or via the Zum app on iOS/Android. | ||
| 60 | ##Command: //rfrcon <**NetbridgeID**> DALIGLOBALADDRESS <**Action**>// | ||
| |
1.2 | 61 | **Action**: 0=stop, 1=start, 3=get status |
| |
13.1 | 62 | Example (NETBRIDGE RF-ID 1A): //rfrcon 1A DALIGLOBALADDRESS 1//## |
| 63 | ))) | ||
| |
1.3 | 64 | 1. Create DALI Groups. If group already exists then go to step 3. This must be done from the gateway console. |
| |
13.1 | 65 | ##Command: //rfrcon <**NetbridgeID**> DALIGROUPADDDELETE <**GroupID**> <**Operation**> <**GroupName**>// |
| |
1.2 | 66 | **GroupID: **0 to 15 |
| 67 | **Operation:** 0=Delete Group, 1=Add Intensity Group, 3=Add Color Group | ||
| |
1.3 | 68 | **GroupName: **Name of the group, no spaces, 16 characters max |
| |
15.1 | 69 | Example (NETBRIDGE RF-ID 1A): //rfrcon 1A DALIGROUPADDDELETE 7 3 TypeF1-Color//## |
| |
14.1 | 70 | 1. Set Scene settings for Color Support. Enables or uses a fixed value for color temperature on color groups. This must be done for all scenes that will be used. |
| |
13.1 | 71 | ##Command: rfrcon <**NetbridgeID**> DALIGROUPCOMMAND 4 <**GroupID**> <**SceneID**> <**SceneLevel**> <**Action**> <**FadeTime**> |
| |
9.1 | 72 | **GroupID**: 0 to 15 (odd for color) |
| |
1.7 | 73 | **SceneID**: Scene number (1 to 16) |
| 74 | **SceneLevel**: 255 for ShowRunner control, 0-254 for fixed scene level | ||
| |
4.1 | 75 | **Action**: 0=Remove Scene, 1=Add Scene |
| |
1.7 | 76 | **FadeTime**: Fade time in 1/10th of a second |
| |
14.1 | 77 | Example (NETBRIDGE RF-ID 1A): //rfrcon 1A DALIGROUPCOMMAND 4 7 1 255 1 10// |
| |
15.1 | 78 | Example (NETBRIDGE RF-ID 1A): //rfrcon 1A DALIGROUPCOMMAND 4 7 2 255 1 10//## |