Skip to Content

Wiki source code of Zummesh Dynamic White/CCT

Version 12.1 by Mark Kohlmann on 2026/01/08 16:34
Show last authors
1 {{warning}}
2 Caveats:
3
4 * Only intensity/CCT fixtures are supported.  This will not work with warm/cool fixtures.
5 * NETBRIDGE must be attached to the ZUMMESH-JBOX-DALI.  Only 1 ZUMMESH-JBOX-DALI is supported per room.  Use Zum Wired or DIN-DALI-2/DIN-DLI if more capabilities are needed.
6 * Supports up to 8 CCT channels, DALI Groups 2,4,6,8,10,12,14,16 on the Zum app (0 based - 1,3,5,7,9,11,13,15 for ShowRunner/console purposes)
7 * Zum Scene must have the CCT channel set to 255 to accept input from ShowRunner.  Values of 0-254 will be sent directly to the group as fixed colors.
8 * Setup must be done from the gateway console
9 * **Loads must be manually changed to BusIndex 3 in the config or added from the UI with BusIndex 3.  Normally DALI loads are BusIndex 2.**
10 {{/warning}}
11
12 Zum wireless supports dynamic white using DALI Groups 2,4,6,8,10,12,14,16 (1,3,5,7,9,11,13,15 for showrunner/console purposes).  Setup must be performed manually on the NETBRIDGE.  Once done, ShowRunner can use the CCT channels to provide CCT data to the fixtures.  Input from ShowRunnerCLC™ requires setting the scene recall for the CCT group to 255.  Any value of 0-254 will be sent to the CCT channel directly and the input from ShowRunnerCLC™ will be ignored.
13
14 ==== Typical Setup for up to 6 zones, 5 fixture types: ====
15
16 (% border="1" style="width:600px" %)
17 |=DALI Group|=Name|=Fixture Type|=Control Type
18 |0|Downlights, Main|F0|Intensity
19 |1|Downlights, Main/Screen CCT|F0|Color
20 |2|Accent Lights|F1a|Intensity
21 |3|Accent Lights CCT|F1a|Color
22 |4|Spot Lights|F3|Intensity
23 |5|Spot Lights CCT|F3|Color
24 |6|Troffers|F4c|Intensity
25 |7|Troffers CCT|F4c|Color
26 |8|Linear|F9|Intensity
27 |9|Linear|F9|Color
28 |10|Downlights @ Screen|F0|Intensity
29 |11|-|-|Color
30 |12|-|-|Intensity
31 |13|-|-|Color
32 |14|-|-|Intensity
33 |15|-|-|Color
34
35 ==== Setup Steps: ====
36
37 1. Address all DALI drivers attached to the JBOX.  This can be done via the gateway console or via the Zum app on iOS/Android.
38 Command: //rfrcon <**NetbridgeID**> DALIGLOBALADDRESS <**Action**>//
39 **Action**: 0=stop, 1=start, 3=get status
40 Example (NETBRIDGE RF-ID 1A): //rfrcon 1A DALIGLOBALADDRESS 1//
41 1. Create DALI Groups.  If group already exists then go to step 3. This must be done from the gateway console.
42 Command: //rfrcon <**NetbridgeID**> DALIGROUPADDDELETE <**GroupID**> <**Operation**> <**GroupName**>//
43 **GroupID: **0 to 15
44 **Operation:** 0=Delete Group, 1=Add Intensity Group, 3=Add Color Group
45 **GroupName: **Name of the group, no spaces, 16 characters max
46 Example (NETBRIDGE RF-ID 1A): //rfrcon 1A DALIGROUPADDDELETE 8 3 TypeF1-Color//
47 1. Modify DALI Group to color, only needed if step 2 was not done.  If step 2 was performed skip this step.
48 Command: //rfrcon <**NetbridgeID**> DALIGROUPSETTWRITE <**GroupID**> 14 <**GroupType**>//
49 **GroupID: **0 to 15
50 **GroupType:** 0=Intensity, 1=Color
51 Example: (NETBRIDGE RF-ID 1A): //rfrcon 1A DALIGROUPSETTWRITE 8 14 1//
52 1. Set Scene settings for Color Support.  Enables or uses a fixed value for color temperature on color groups.
53 Command: rfrcon <**NetbridgeID**> DALIGROUPCOMMAND 4 <**GroupID**> <**SceneID**> <**SceneLevel**> <**Action**> <**FadeTime**>
54 **GroupID**: 0 to 15 (odd for color)
55 **SceneID**: Scene number (1 to 16)
56 **SceneLevel**: 255 for ShowRunner control, 0-254 for fixed scene level
57 **Action**: 0=Remove Scene, 1=Add Scene
58 **FadeTime**: Fade time in 1/10th of a second
59 Example (NETBRIDGE RF-ID 1A): //rfrcon 1A DALIGROUPCOMMAND 4 8 1 255 1 10//
60 Example (NETBRIDGE RF-ID 1A): //rfrcon 1A DALIGROUPCOMMAND 4 15 1 255 1 10//