Skip to Content

Changes for page Zummesh Dynamic White/CCT

Last modified by Mark Kohlmann on 2026/01/08 20:58
From version 3.1
edited by Craig Lewis
on 2021/09/07 21:39
Change comment: There is no comment for this version
To version 16.1
edited by Mark Kohlmann
on 2026/01/08 20:58
Change comment: There is no comment for this version

Summary

Details

Page properties
Parent
... ... @@ -1,1 +1,1 @@
1 -SHOWRUNNER™ User Guide & Wiki.Troubleshooting.WebHome
1 +SHOWRUNNER™ Setup Guide.Troubleshooting Guide.Advanced Tools.WebHome
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.craig\.lewis@chiefintegrations\.com
1 +XWiki.mark\.kohlmann@chiefintegrations\.com
Content
... ... @@ -1,59 +1,79 @@
1 -Zum wireless supports dynamic white using DALI Groups 9-16 (8 to 15 for console purposes).  Setup must be performed manually on the NETBRIDGE.  Once done, ShowRunner can use the CCT channels to provide CCT data to the fixtures.  Input from ShowRunner requires setting the scene recall for the CCT group to 255.  Any value of 0-254 will be sent to the CCT channel directly and the input from ShowRunner will be ignored.
1 +{{warning}}
2 +Caveats:
2 2  
3 -==== Typical Setup for up to 6 zones, 5 fixture types: ====
4 +* Only intensity/CCT fixtures are supported.  This will not work with warm/cool fixtures.
5 +* NETBRIDGE must be attached to the ZUMMESH-JBOX-DALI.  Only 1 ZUMMESH-JBOX-DALI is supported per room.  Use Zum Wired or DIN-DALI-2/DIN-DLI if more capabilities are needed.
6 +* Supports up to 8 CCT channels, DALI Groups 2,4,6,8,10,12,14,16 on the Zum app (0 based - 1,3,5,7,9,11,13,15 for ShowRunner/console purposes)
7 +* Zum Scene must have the CCT channel set to 255 to accept input from ShowRunner.  Values of 0-254 will be sent directly to the group as fixed colors.
8 +* Setup must be done from the gateway console
9 +* **Loads must be manually changed to BusIndex 3 in the ShowRunner config or added from the UI with BusIndex 3.  Normally DALI loads are BusIndex 2.**
10 +{{/warning}}
4 4  
5 -==== ====
12 +Zum wireless supports dynamic white using DALI Groups 2,4,6,8,10,12,14,16 (1,3,5,7,9,11,13,15 for ShowRunner/console purposes).  Setup must be performed manually on the NETBRIDGE.  Once done, ShowRunner can use the CCT channels to provide CCT data to the fixtures.  Input from ShowRunnerCLC™ requires setting the scene recall for the CCT group to 255.  Any value of 0-254 will be sent to the CCT channel directly and the input from ShowRunnerCLC™ will be ignored.
6 6  
7 -(% border="1" style="width:500px" %)
14 +==== Typical Setup for up to 6 zones, 5 fixture types: ====
15 +
16 +(% border="1" style="width:600px" %)
8 8  |=DALI Group|=Name|=Fixture Type|=Control Type
9 9  |0|Downlights, Main|F0|Intensity
10 -|1|Accent Lights|F1a|Intensity
11 -|2|Spot Lights|F3|Intensity
12 -|3|Troffers|F4c|Intensity
13 -|4|Linear|F9|Intensity
14 -|5|Downlights @ Screen|F0|Intensity
15 -|6|-|-|Intensity
16 -|7|-|-|Intensity
17 -|8|Downlights CCT|F0|Color
18 -|9|Accent Lights CCT|F1a|Color
19 -|10|Spot Lights CCT|F3|Color
20 -|11|Troffers CCT|F4c|Color
21 -|12|Linear CCT|F9|Color
19 +|1|Downlights, Main/Screen CCT|F0|Color
20 +|2|Accent Lights|F1a|Intensity
21 +|3|Accent Lights CCT|F1a|Color
22 +|4|Spot Lights|F3|Intensity
23 +|5|Spot Lights CCT|F3|Color
24 +|6|Troffers|F4c|Intensity
25 +|7|Troffers CCT|F4c|Color
26 +|8|Linear|F9|Intensity
27 +|9|Linear|F9|Color
28 +|10|Downlights @ Screen|F0|Intensity
29 +|11|-|-|Color
30 +|12|-|-|Intensity
22 22  |13|-|-|Color
23 -|14|-|-|Color
32 +|14|-|-|Intensity
24 24  |15|-|-|Color
25 25  
26 -==== Caveats: ====
35 +==== Setup Steps: ====
27 27  
28 -* Only intensity/CCT fixtures are supported.  This will not work with warm/cool fixtures.
29 -* NETBRIDGE must be attached to the ZUMMESH-JOBX-DALI.  Only 1 ZUMMESH-JBOX-DALI is supported per room.  Use Zum Wired or DIN-DALI-2 if more capabilities are needed.
30 -* Supports up to 8 CCT channels, DALI Groups 9-16 (8 to 15 for console purposes)
31 -* Zum Scene must have the CCT channel set to 255 to accept input from ShowRunner.  Values of 0-254 will be sent directly to the group as fixed colors.
32 -* Setup must be done from the gateway console
33 33  
34 -==== Setup Steps: ====
38 +If your DALI groups are already commissioned and you need to specify the groups for color (Examples shown for group 7):
35 35  
36 -1. Address all DALI drivers attached to the JBOX.  This can be done via the gateway console or via the Zum app on iOS/Android.
37 -Command: //rfrcon <**NetbridgeID**> DALIGLOBALADDRESS <**Action**>//
40 +1. Modify DALI Group to color, only needed if step 2 was not done.  If step 2 was performed skip this step.
41 +##Command: //rfrcon <**NetbridgeID**> DALIGROUPSETTWRITE <**GroupID**> 14 <**GroupType**>//
42 +**GroupID: **0 to 15
43 +**GroupType:** 0=Intensity, 1=Color
44 +Example: (NETBRIDGE RF-ID 1A): //rfrcon 1A DALIGROUPSETTWRITE 7 14 1//##
45 +1. Set Scene settings for Color Support.  Enables or uses a fixed value for color temperature on color groups.  This must be done for all scenes that will be used.
46 +##Command: rfrcon <**NetbridgeID**> DALIGROUPCOMMAND 4 <**GroupID**> <**SceneID**> <**SceneLevel**> <**Action**> <**FadeTime**>
47 +**GroupID**: 0 to 15 (odd for color)
48 +**SceneID**: Scene number (1 to 16)
49 +**SceneLevel**: 255 for ShowRunner control, 0-254 for fixed scene level
50 +**Action**: 0=Remove Scene, 1=Add Scene
51 +**FadeTime**: Fade time in 1/10th of a second
52 +Example (NETBRIDGE RF-ID 1A): //rfrcon 1A DALIGROUPCOMMAND 4 7 1 255 1 10//
53 +Example (NETBRIDGE RF-ID 1A): //rfrcon 1A DALIGROUPCOMMAND 4 7 2 255 1 10//##
54 +1. Change the area to a different scene and then back to a scene that has color enabled to permit the receiving of color commands.
55 +
56 +If Starting from scratch without having been commissioned in the Zum App (Examples shown for group 7):
57 +
58 +1. (((
59 +Address all DALI drivers attached to the JBOX.  This can be done via the gateway console or via the Zum app on iOS/Android.
60 +##Command: //rfrcon <**NetbridgeID**> DALIGLOBALADDRESS <**Action**>//
38 38  **Action**: 0=stop, 1=start, 3=get status
39 -Example (NETBRIDGE RF-ID 1A): //rfrcon 1A DALIGLOBALADDRESS 1//
62 +Example (NETBRIDGE RF-ID 1A): //rfrcon 1A DALIGLOBALADDRESS 1//##
63 +)))
40 40  1. Create DALI Groups.  If group already exists then go to step 3. This must be done from the gateway console.
41 -Command: //rfrcon <**NetbridgeID**> DALIGROUPADDDELETE <**GroupID**> <**Operation**> <**GroupName**>//
65 +##Command: //rfrcon <**NetbridgeID**> DALIGROUPADDDELETE <**GroupID**> <**Operation**> <**GroupName**>//
42 42  **GroupID: **0 to 15
43 43  **Operation:** 0=Delete Group, 1=Add Intensity Group, 3=Add Color Group
44 44  **GroupName: **Name of the group, no spaces, 16 characters max
45 -Example (NETBRIDGE RF-ID 1A): //rfrcon 1A DALIGROUPADDDELETE 8 3 TypeF1-Color//
46 -1. Modify DALI Group to color, only needed if step 2 was not done.  If step 2 was performed skip this step.
47 -Command: //rfrcon <**NetbridgeID**> DALIGROUPSETTWRITE <**GroupID**> 14 <**GroupType**>//
48 -**GroupID: **0 to 15
49 -**GroupType:** 0=Intensity, 1=Color
50 -Example: (NETBRIDGE RF-ID 1A): //rfrcon 1A DALIGROUPSETTWRITE 8 14 1//
51 -1. Set Scene settings for Color Support.  Enables or uses a fixed value for color temperature on color groups.
52 -Command: rfrcon <**NetbridgeID**> DALIGROUPCOMMAND 4 <**GroupID**> <**SceneID**> <**SceneLevel**> <**AnalogInput**> <**FadeTime**>
53 -**GroupID**: 8 to 15
69 +Example (NETBRIDGE RF-ID 1A): //rfrcon 1A DALIGROUPADDDELETE 7 3 TypeF1-Color//##
70 +1. Set Scene settings for Color Support.  Enables or uses a fixed value for color temperature on color groups.  This must be done for all scenes that will be used.
71 +##Command: rfrcon <**NetbridgeID**> DALIGROUPCOMMAND 4 <**GroupID**> <**SceneID**> <**SceneLevel**> <**Action**> <**FadeTime**>
72 +**GroupID**: 0 to 15 (odd for color)
54 54  **SceneID**: Scene number (1 to 16)
55 55  **SceneLevel**: 255 for ShowRunner control, 0-254 for fixed scene level
56 -**AnalogInput**: Analog input to use from the control system, should be equal to **GroupID **- 7
75 +**Action**: 0=Remove Scene, 1=Add Scene
57 57  **FadeTime**: Fade time in 1/10th of a second
58 -Example (NETBRIDGE RF-ID 1A): //rfrcon 1A DALIGROUPCOMMAND 4 8 1 255 1 10//
59 -Example (NETBRIDGE RF-ID 1A): //rfrcon 1A DALIGROUPCOMMAND 4 15 1 255 8 10//
77 +Example (NETBRIDGE RF-ID 1A): //rfrcon 1A DALIGROUPCOMMAND 4 7 1 255 1 10//
78 +Example (NETBRIDGE RF-ID 1A): //rfrcon 1A DALIGROUPCOMMAND 4 7 2 255 1 10//##
79 +1. Change the area to a different scene and then back to a scene that has color enabled to permit the receiving of color commands.