Skip to Content

Changes for page Zummesh Dynamic White/CCT

Last modified by Mark Kohlmann on 2026/01/08 20:58
From version 16.1
edited by Mark Kohlmann
on 2026/01/08 20:58
Change comment: There is no comment for this version
To version 12.1
edited by Mark Kohlmann
on 2026/01/08 16:34
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -6,10 +6,10 @@
6 6  * Supports up to 8 CCT channels, DALI Groups 2,4,6,8,10,12,14,16 on the Zum app (0 based - 1,3,5,7,9,11,13,15 for ShowRunner/console purposes)
7 7  * Zum Scene must have the CCT channel set to 255 to accept input from ShowRunner.  Values of 0-254 will be sent directly to the group as fixed colors.
8 8  * Setup must be done from the gateway console
9 -* **Loads must be manually changed to BusIndex 3 in the ShowRunner config or added from the UI with BusIndex 3.  Normally DALI loads are BusIndex 2.**
9 +* **Loads must be manually changed to BusIndex 3 in the config or added from the UI with BusIndex 3.  Normally DALI loads are BusIndex 2.**
10 10  {{/warning}}
11 11  
12 -Zum wireless supports dynamic white using DALI Groups 2,4,6,8,10,12,14,16 (1,3,5,7,9,11,13,15 for ShowRunner/console purposes).  Setup must be performed manually on the NETBRIDGE.  Once done, ShowRunner can use the CCT channels to provide CCT data to the fixtures.  Input from ShowRunnerCLC™ requires setting the scene recall for the CCT group to 255.  Any value of 0-254 will be sent to the CCT channel directly and the input from ShowRunnerCLC™ will be ignored.
12 +Zum wireless supports dynamic white using DALI Groups 2,4,6,8,10,12,14,16 (1,3,5,7,9,11,13,15 for showrunner/console purposes).  Setup must be performed manually on the NETBRIDGE.  Once done, ShowRunner can use the CCT channels to provide CCT data to the fixtures.  Input from ShowRunnerCLC™ requires setting the scene recall for the CCT group to 255.  Any value of 0-254 will be sent to the CCT channel directly and the input from ShowRunnerCLC™ will be ignored.
13 13  
14 14  ==== Typical Setup for up to 6 zones, 5 fixture types: ====
15 15  
... ... @@ -34,46 +34,27 @@
34 34  
35 35  ==== Setup Steps: ====
36 36  
37 -
38 -If your DALI groups are already commissioned and you need to specify the groups for color (Examples shown for group 7):
39 -
40 -1. Modify DALI Group to color, only needed if step 2 was not done.  If step 2 was performed skip this step.
41 -##Command: //rfrcon <**NetbridgeID**> DALIGROUPSETTWRITE <**GroupID**> 14 <**GroupType**>//
42 -**GroupID: **0 to 15
43 -**GroupType:** 0=Intensity, 1=Color
44 -Example: (NETBRIDGE RF-ID 1A): //rfrcon 1A DALIGROUPSETTWRITE 7 14 1//##
45 -1. Set Scene settings for Color Support.  Enables or uses a fixed value for color temperature on color groups.  This must be done for all scenes that will be used.
46 -##Command: rfrcon <**NetbridgeID**> DALIGROUPCOMMAND 4 <**GroupID**> <**SceneID**> <**SceneLevel**> <**Action**> <**FadeTime**>
47 -**GroupID**: 0 to 15 (odd for color)
48 -**SceneID**: Scene number (1 to 16)
49 -**SceneLevel**: 255 for ShowRunner control, 0-254 for fixed scene level
50 -**Action**: 0=Remove Scene, 1=Add Scene
51 -**FadeTime**: Fade time in 1/10th of a second
52 -Example (NETBRIDGE RF-ID 1A): //rfrcon 1A DALIGROUPCOMMAND 4 7 1 255 1 10//
53 -Example (NETBRIDGE RF-ID 1A): //rfrcon 1A DALIGROUPCOMMAND 4 7 2 255 1 10//##
54 -1. Change the area to a different scene and then back to a scene that has color enabled to permit the receiving of color commands.
55 -
56 -If Starting from scratch without having been commissioned in the Zum App (Examples shown for group 7):
57 -
58 -1. (((
59 -Address all DALI drivers attached to the JBOX.  This can be done via the gateway console or via the Zum app on iOS/Android.
60 -##Command: //rfrcon <**NetbridgeID**> DALIGLOBALADDRESS <**Action**>//
37 +1. Address all DALI drivers attached to the JBOX.  This can be done via the gateway console or via the Zum app on iOS/Android.
38 +Command: //rfrcon <**NetbridgeID**> DALIGLOBALADDRESS <**Action**>//
61 61  **Action**: 0=stop, 1=start, 3=get status
62 -Example (NETBRIDGE RF-ID 1A): //rfrcon 1A DALIGLOBALADDRESS 1//##
63 -)))
40 +Example (NETBRIDGE RF-ID 1A): //rfrcon 1A DALIGLOBALADDRESS 1//
64 64  1. Create DALI Groups.  If group already exists then go to step 3. This must be done from the gateway console.
65 -##Command: //rfrcon <**NetbridgeID**> DALIGROUPADDDELETE <**GroupID**> <**Operation**> <**GroupName**>//
42 +Command: //rfrcon <**NetbridgeID**> DALIGROUPADDDELETE <**GroupID**> <**Operation**> <**GroupName**>//
66 66  **GroupID: **0 to 15
67 67  **Operation:** 0=Delete Group, 1=Add Intensity Group, 3=Add Color Group
68 68  **GroupName: **Name of the group, no spaces, 16 characters max
69 -Example (NETBRIDGE RF-ID 1A): //rfrcon 1A DALIGROUPADDDELETE 7 3 TypeF1-Color//##
70 -1. Set Scene settings for Color Support.  Enables or uses a fixed value for color temperature on color groups.  This must be done for all scenes that will be used.
71 -##Command: rfrcon <**NetbridgeID**> DALIGROUPCOMMAND 4 <**GroupID**> <**SceneID**> <**SceneLevel**> <**Action**> <**FadeTime**>
46 +Example (NETBRIDGE RF-ID 1A): //rfrcon 1A DALIGROUPADDDELETE 8 3 TypeF1-Color//
47 +1. Modify DALI Group to color, only needed if step 2 was not done.  If step 2 was performed skip this step.
48 +Command: //rfrcon <**NetbridgeID**> DALIGROUPSETTWRITE <**GroupID**> 14 <**GroupType**>//
49 +**GroupID: **0 to 15
50 +**GroupType:** 0=Intensity, 1=Color
51 +Example: (NETBRIDGE RF-ID 1A): //rfrcon 1A DALIGROUPSETTWRITE 8 14 1//
52 +1. Set Scene settings for Color Support.  Enables or uses a fixed value for color temperature on color groups.
53 +Command: rfrcon <**NetbridgeID**> DALIGROUPCOMMAND 4 <**GroupID**> <**SceneID**> <**SceneLevel**> <**Action**> <**FadeTime**>
72 72  **GroupID**: 0 to 15 (odd for color)
73 73  **SceneID**: Scene number (1 to 16)
74 74  **SceneLevel**: 255 for ShowRunner control, 0-254 for fixed scene level
75 75  **Action**: 0=Remove Scene, 1=Add Scene
76 76  **FadeTime**: Fade time in 1/10th of a second
77 -Example (NETBRIDGE RF-ID 1A): //rfrcon 1A DALIGROUPCOMMAND 4 7 1 255 1 10//
78 -Example (NETBRIDGE RF-ID 1A): //rfrcon 1A DALIGROUPCOMMAND 4 7 2 255 1 10//##
79 -1. Change the area to a different scene and then back to a scene that has color enabled to permit the receiving of color commands.
59 +Example (NETBRIDGE RF-ID 1A): //rfrcon 1A DALIGROUPCOMMAND 4 8 1 255 1 10//
60 +Example (NETBRIDGE RF-ID 1A): //rfrcon 1A DALIGROUPCOMMAND 4 15 1 255 1 10//