Wiki source code of ZUMNET-JBOX-DALI Configuration Options
Last modified by Craig Lewis on 2025/10/20 15:33
Hide last authors
| author | version | line-number | content |
|---|---|---|---|
 |
4.1 | 1 | The Crestron ZUMNET-JBOX-DALI can be configured in two different modes. App mode or Legacy mode (DIN-DALI-2 emulation). |
| |
1.1 | 2 | |
| |
4.1 | 3 | (% class="box warningmessage" %) |
| 4 | ((( | ||
| 5 | Minimum supported ZUMNET firmware version is PUF zum-wired_1.03.27.puf. | ||
| |
8.1 | 6 | \\ShowRunner Version Minimum: 3.20. |
| 7 | |||
| 8 | Zum Discovery is only intended for ZUMNET-JBOX-DALI commissioned in App Mode. Legacy Mode requires manual setup, similar to setting up a DIN-DALI-2. | ||
| |
4.1 | 9 | ))) |
| 10 | |||
| |
1.1 | 11 | (% style="margin-right:auto; width:800px" %) |
| 12 | |=Function|=APP Mode|=Legacy Mode | ||
| |
2.1 | 13 | |Address and Group Fixtures|Zum App on Phone/Tablet|((( |
| |
5.1 | 14 | * ShowRunnerCLC™ UI |
| |
6.1 | 15 | * Toolbox DALI Commissioning Tool 2.0 |
| |
2.1 | 16 | * Console (same as DIN-DALI-2) |
| |
1.1 | 17 | ))) |
| |
2.1 | 18 | |Lighting Logic|Internal to Zum Room, can be enhanced by showrunner|((( |
| |
5.1 | 19 | ShowRunnerCLC™ only, same as DIN-DALI-2 |
| |
1.1 | 20 | ))) |
| |
7.1 | 21 | |showrunner Controller Type (Model)|(% style="width:350px" %)//ZUMNET-JBOX-DALI//|(% style="width:350px" %)//ZUMNET-JBOX-DALI-LEGACY// |
| |
2.1 | 22 | |Configuration Steps|(% style="width:350px" %)((( |
| 23 | 1. Update Firmware to 1.3.27 puf or later | ||
| 24 | 1. Connect to ZUMNET-JBOX Console | ||
| 25 | 1. Enter Command: //DALISETMODE 1 2// | ||
| 26 | 1. Wait 5 seconds, ZUMNET JBOX should reboot, if not reboot | ||
| 27 | 1. Enter Command: //ZWMODE ZUM// | ||
| 28 | 1. Reboot | ||
| 29 | )))|(% style="width:350px" %)((( | ||
| 30 | 1. Update Firmware to 1.3.27 puf or later | ||
| 31 | 1. Connect to ZUMNET-JBOX Console | ||
| 32 | 1. Enter Command: //ZWMODE CNET// | ||
| 33 | 1. Reboot | ||
| 34 | 1. Enter Command: //DALISETMODE 1 1// | ||
| 35 | 1. Wait 5 seconds, ZUMNET JBOX should reboot, if not reboot | ||
| 36 | ))) | ||
| 37 | |Known Issues|((( | ||
| 38 | * All fixtures/groups must be setup through the app. If not done through the app then controls do not work from the app or showrunner. There is no way to discover existing groupings. Requires complete re-address and group. | ||
| 39 | * TEST button only controls defined groups and not broadcast (Crestron says they will revert this back to broadcast in a future release) | ||
| 40 | )))| |