Skip to Content

Changes for page TSW Touchpanel Setup

Last modified by Alexander Mott on 2025/03/14 16:19
From version 3.1
edited by Alexander Mott
on 2022/06/13 15:14
Change comment: There is no comment for this version
To version 6.1
edited by Alexander Mott
on 2022/06/13 16:11
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -6,7 +6,11 @@
6 6  
7 7  === IP Configuration ===
8 8  
9 -*
9 +TSWs should be configured with static IP addresses in the same range as the processor. This can be done from the TSW itself by entering into setup mode:
10 +
11 +* Put 5 fingers on the front of the TSW and hold for approximately 10 seconds until the TSW enters setup mode
12 +** TSW-xx70 series or TSW-xx60 series with authentication enabled will require admin credentials
13 +** If this is the first time entering setup, it will prompt for a username and password in order to create an admin account. Do not lose or forget these credentials.
10 10  * Set the TS/TSWs IP Address per your network requirements (If using a panel other than TSW-770 you will need the CI_ShowRunner-UI_v3.xx PUF)
11 11  * Connect the PUF (CI_ShowRunner_v3.xx) to the TSW to load the UI
12 12  ** Only add CI_ShowRunner-UI_v3.xx if using touch panel other than TSW-770.  
... ... @@ -15,14 +15,15 @@
15 15  
16 16  If operating on a network with a DHCP server (either by running DHCP server software on your computer, or if the processor has a control subnet or is running the [[SHOWRUNNER™ DHCP Server>>doc:SHOWRUNNER™ User Guide & Wiki.Troubleshooting.DHCP Server.WebHome]]), then it is possible to configure these settings via Ethernet using Text Console:
17 17  
18 -*
19 -* Once connected, open Text Console and run the following commands to configure the processor's IP settings (example is for a 10.0.0.0/24 subnet, with a TSW IP address of 10.0.0.19, a TSW IP-ID of 10, and a processor IP address of 10.0.0.10)
20 -** Disable DHCP: dhcp 0 off
21 -** Set IP address: ipa 0 10.0.0.10
22 -** Set IP subnet mask: ipm 0 255.255.255.0
23 -** Set default gateway: defr 0 10.0.0.1
24 -** Set hostname: host AP3-CPP
25 -** Reboot the processor: reboot
22 +* On jobs with multiple TSWs, they can be identified using Device Discovery and matching the MAC address of the TSW to the IP address assigned by the DHCP server
23 +* Once connected, open Text Console and run the following commands to configure the processor's IP settings (example is for a **10.0.0.0(% style="color:darkgoldenrod" %)/24(%%)** subnet, with a TSW IP address of (% style="color:blue" %)**10.0.0.19**(%%), a TSW IP-ID of (% style="color:olive" %)**10**(%%), a processor IP address of (% style="color:orange" %)**10.0.0.10**(%%), and a TSW hostname of (% style="color:purple" %)**TSW-L1**(%%))
24 +** Disable DHCP: ##dhcp 0 off##
25 +** Set IP address: ##ipa 0 (% style="color:blue" %)**10.0.0.19**(%%)##
26 +** Set IP subnet mask: ##ipm 0 (% style="color:darkgoldenrod" %)**255.255.255.0**(%%)##
27 +** Set default gateway: ##defr 0 **10.0.0.1**##
28 +** Update IP table: ##addm (% style="color:olive" %)**10**(%%) (% style="color:orange" %)**10.0.0.10**(%%)##
29 +** Set hostname: ##host (% style="color:purple" %)**TSW-L1**(%%)##
30 +** Reboot the TSW: ##reboot##
26 26  
27 27  === Load the SHOWRUNNER™ Project ===
28 28