Changes for page Crestron RF Gateway Setup

Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -62,7 +62,7 @@
62	62	** Close the tool once the change has been applied
63	63	* Once the RF channel has been updated, verify it by running the command: ##rfchannel## without any parameters
64	64
65		-= Acquiring Devices =
	65	+= Acquiring and Addressing Devices =
66	66
67	67	(% class="box warningmessage" %)
68	68	(((
...	...	@@ -84,22 +84,25 @@
84	84	*** Wait for the confirmation dialog and click "OK" to close the confirmation dialog
85	85	*** Previously acquired devices will be displayed with black text, while newly acquired devices will populate with blue text
86	86	*** Using the Gateway Configuration tool to acquire hardware may be preferable to using Text Console as acquired devices will report their Serial Number as they are acquired instead of just their TSID
87		-* Acquire all necessary devices to the gateway
88		-** The process for acquiring a wireless device to a gateway varies for each model, but generally the procedure is as follows:
89		-** Press the
90		-* Take the CEN-GWEXER out of acquire mode
	87	+* The process for acquiring a wireless device to a gateway varies for each model, but generally the procedure is as follows:
	88	+** Press the "setup" button (top button for keypads) in the sequence press-press-press-hold
	89	+** Do not release the button until the setup LED (top feedback LED for keypads) begins blinking slowly
	90	+*** If the setup LED turns steady, then the device was acquired successfully
	91	+*** If the setup LED begins to rapidly blink, then the acquire failed
	92	+**** Press the "setup" button again to cancel acquire
	93	+**** Attempt to acquire the device again
	94	+**** If the device fails to acquire a second time: verify that the correct gateway is in acquire mode, verify that no other gateways are in acquire mode, verify that the desired gateway is close enough to the device that it should be able to acquire, and verify that there are no other sources of RF interference that may be preventing acquisition.
	95	+** Repeat for all wireless devices that need to be acquired to the gateway
	96	+* Once all devices have been acquired, take the CEN-GWEXER out of acquire mode:
91	91	** If using Text Console, run the command: ##acquire stop##
92		-** If
93		-*
94		-*
95		-* Once devices have been acquired, use the text console command: reportnetdev to view the network ID
	98	+** If using the Gateway Configuration tool, click the "STOP Acquire" button in the lower left
	99	+* Address devices as indicated in the SHOWRUNNER™ takeoff by either:
	100	+** Use Text Console to run the command: ##setrfidbytsid [CID] [TSID]##
	101	+*** Replace "[CID]" with the connection ID as indicated in the takeoff
	102	+*** Replace "[TSID]" with the 4-byte, hexadecimal TSID of the device to be addressed
	103	+** Use Network Device Tree View to select each device and address them individually
	104	+* Verify all devices have been acquired and addressed correctly using Network Device Tree View or with the Text Console command: ##reportnetdev##
96	96
97		-~/~/1-2-3-hold on 4 until all lights blink, then release
98		-top light will blink slowly a few times and then hold solid or start blinking rapidly
99		-if rapid blinking, cancel acquire and make sure that rf gateway is in acquire mode and device is in range then repeat to put device into acquire mode
100		-
101		-~/~/"rep" to show acquired devices
102		-
103	103	= Moving/Removing Devices (Unacquiring Devices) =
104	104
105	105	When a wireless Crestron device is acquired to a new gateway using the typical acquiring process described above, it will automatically forget the previously connected gateway. The gateway itself, however, must manually "forget" the previously connected device before a newly acquired and addressed device will function correctly. This is necessary whether the originally connected device is moved or if the originally corrected device has failed and is being replaced.