Changes for page Crestron RF Gateway Setup

Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -8,44 +8,19 @@
8	8
9	9	= IP Configuration =
10	10
11		-Typically, each CEN-GWEXER will need to be initially configured via USB (micro USB), unless their MAC addresses are already known and the lighting network has a DHCP server (either by running DHCP server software on your computer, or if the processor has a control subnet or is running the [[ShowRunner™ DHCP Server>>doc:SHOWRUNNER™ Setup Guide.Troubleshooting Guide.Advanced Tools.DHCP Server.WebHome]]).
	11	+Lorem
12	12
13		-CEN-GWEXERs  for the first time, it may be necessary to manually change the connection type from "Auto" to "SSL"
14		-
15		-Whether connected to the CEN-GWEXER via USB or Ethernet, the process to configure the static IP addresses is the same:
16		-
17		-* Open Text Console in Toolbox and connect to the CEN-GWEXER
18		-** Note that you may need to manually select "SSL" connection type, as "Auto" might not always redirect
19		-* Run the following commands to configure the CEN-GWEXER's static IP settings (example is for a **10.0.0.0(% style="color:darkgoldenrod" %)/24(%%)** subnet, with a static IP address of (% style="color:blue" %)**10.0.0.12**(%%), an IP-ID of (% style="color:olive" %)**C1**(%%), and a target processor IP address of (% style="color:orange" %)**10.0.0.10**(%%), and a device hostname of (% style="color:purple" %)**GWEXER-L1**(%%))
20		-** Set IP address: ##ipa 0 (% style="color:blue" %)**10.0.0.12**(%%)##
21		-** Set IP subnet mask: ##ipm 0 (% style="color:darkgoldenrod" %)**255.255.255.0**(%%)##
22		-** Set default gateway: ##defr 0 **10.0.0.1**##
23		-** Disable DHCP: ##dhcp off##
24		-** Update IP table: ##addm (% style="color:olive" %)**C1**(%%) (% style="color:orange" %)**10.0.0.10**(%%)##
25		-** Set hostname: ##host (% style="color:purple" %)**GWEXER-L1**(%%)##
26		-** Reboot the CEN-GWEXER: ##reboot##
27		-* Repeat for all CEN-GWEXERs on the job
28		-
29	29	= SSL Setup =
30	30
31		-Crestron devices that support SSL require the use of a secure connection between the processor and the device. In order to establish this secure connection, the processor must have authentication enabled and there must be a user on the processor with "Connects" group permissions.
	15	+Lorem
32	32
33		-Configure the Connects user on the processor:
	17	+~/~/https:~/~/wiki.chiefintegrations.com/SHOWRUNNER%E2%84%A2%20User%20Guide%20%26%20Wiki/SHOWRUNNER%E2%84%A2%20Appendix/SSL%20User%20Configuration/
	18	+SSL setup on proc
	19	+SSL setup on devices
34	34
35		-* Ensure the processor has [[its IP configured and authentication enabled>>doc:SHOWRUNNER™ Setup Guide.SHOWRUNNER™ Installation Guide.SHOWRUNNER™ Installation and Network Setup.Processor Setup.WebHome||anchor="HIPConfiguration"]]
36		-** Verify the processor has authentication enabled by running the command: ##auth## without any parameters
37		-* Create a user by running the following commands, replacing the "username" and "password" with your desired credentials
38		-** ##adduser -N:username -P:password##
39		-** ##addusertogroup -N:username -G:Connects##
40		-* Verify that the user has been created by running the command: ##listusers##
41		-* This process only needs to be performed once per processor on the jobsite
	21	+~/~/Need to manually set SSL/TSL method for connecting to gwexer with auth enabled
	22	+- also need to update address book if gwexer are added to address book (defaults to ctp)
42	42
43		-Configure the CS authentication on the CEN-GWEXER:
44		-
45		-* Run the following command, replacing the "username" and "password" with the credentials of the Connects user from the previous step
46		-** ##setcsauth -N:username -P:password##
47		-* Repeat this process for every CEN-GWEXER on the jobsite
48		-
49	49	= RF Channel =
50	50
51	51	Lorem