Skip to Content

Changes for page Crestron RF Gateway Setup

Last modified by Alexander Mott on 2025/03/12 17:16
From version 25.1
edited by Alexander Mott
on 2024/12/02 18:53
Change comment: There is no comment for this version
To version 28.1
edited by Alexander Mott
on 2024/12/16 23:38
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,6 +1,6 @@
1 -{{warning}}
2 -All RF Gateways require authentication to be configured to connect to the device as well as credentials to be configured for SSL connection with the processor: **the Crestron Agent or Field Tech are responsible for recording these credentials. Chief Integrations provide assistance if the admin credentials are not known. The only way to connect to a device for which the credentials have been lost is to factory reset the device. (% style="color:red" %)All previously acquired devices will need to be re-acquired if the gateway is factory reset.(%%)**​​​​
3 -{{/warning}}
1 +{{error}}
2 +All RF Gateways require authentication to be configured to connect to the device as well as credentials to be configured for SSL connection with the processor: **the Crestron Agent or Field Tech are responsible for recording these credentials. Chief Integrations cannot provide assistance unless the admin credentials are known. The only way to connect to a device for which the credentials have been lost is to factory reset the device. (% style="color:red" %)All previously acquired devices will need to be re-acquired if the gateway is factory reset.(%%)**​​​​
3 +{{/error}}
4 4  
5 5  {{box cssClass="floatinginfobox" title="**CONTENTS**"}}
6 6  {{toc/}}
... ... @@ -10,7 +10,7 @@
10 10  
11 11  Installations using infinetEX or Extended Range devices require the CEN-GWEXER gateway, while Zūm Wireless installations require the ZUMNET-GATEWAY. Throughout this article, "CEN-GWEXER" and "infinetEX" will be used to refer to the gateway and the wireless devices respectively.
12 12  
13 -For SHOWRUNNER™ installations, the IP address of the CEN-GWEXER does not matter as long as it is in the same range as the processor and does not conflict with any other devices on the network. Instead, CEN-GWEXERs are identified to the processor via their IP-ID. Note that which infinetEX devices are landed at which CEN-GWEXER matters, and if devices are moved between CEN-GWEXERs then the configuration will need to be updated (see below). Chief Integrations typically provides an SRTakeoff.xlsx spreadsheet with an IP Table tab that lists all the CEN-GWEXER IP-IDs in the program. If no takeoff is provided, then the processor's IP table can be checked by running the ##ipt -t ##command from the processor after the configuration is loaded. CEN-GWEXERs will typically have IP-IDs in the "##Cx##" range.
13 +For SHOWRUNNER™ installations, the IP address of the CEN-GWEXER does not matter as long as it is in the same range as the processor and does not conflict with any other devices on the network. Instead, CEN-GWEXERs are identified to the processor via their IP-ID. Note that which infinetEX devices are landed at which CEN-GWEXER matters, and if devices are moved between CEN-GWEXERs then the configuration will need to be updated (see below). Chief Integrations typically provides an SRTakeoff.xlsx spreadsheet with an IP Table tab that lists all the CEN-GWEXER IP-IDs in the program. If no takeoff is provided, then the processor's IP table can be checked by running the ##ipt -t ##command from the processor after the configuration is loaded. CEN-GWEXERs will typically have IP-IDs in the "##Cx##" range. For Zūm Wireless jobs using the [[Zūm Discovery process>>doc:SHOWRUNNER™ Setup Guide.SHOWRUNNER™ Installation Guide.Program Configuration.Zūm Discovery.WebHome]] , no takeoff is provided as the ZUMNET-GATEWAY IP table will be assigned and consumed at the time of discovery.
14 14  
15 15  = IP Configuration =
16 16