Skip to Content

Changes for page Crestron RF Gateway Setup

Last modified by Alexander Mott on 2025/03/12 17:16
From version 21.1
edited by Alexander Mott
on 2024/10/24 17:14
Change comment: There is no comment for this version
To version 23.1
edited by Alexander Mott
on 2024/10/24 17:34
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -4,7 +4,7 @@
4 4  
5 5  CEN-GWEXERs are a two-way radiofrequency (RF) transceivers that allow Crestron infinetEX and Extended Range wireless devices to communicate with the control processor over Ethernet. They are for Crestron wireless systems what [[DIN-CENCN-2s>>doc:SHOWRUNNER™ Setup Guide.SHOWRUNNER™ Installation Guide.SHOWRUNNER™ Installation and Network Setup.DIN-CENCN-2 Setup.WebHome]] are for wired Cresnet systems.
6 6  
7 -For SHOWRUNNER™ installations, the IP address of the CEN-GWEXER does not matter as long as it is in the same range as the processor and does not conflict with any other devices on the network. Instead, CEN-GWEXERs are identified to the processor via their IP-ID. Note that which infinetEX devices are landed at which CEN-GWEXER matters, and if devices are moved between CEN-GWEXERs then the configuration will need to be updated (see below). Chief Integrations typically provides an SRTakeoff.xlsx spreadsheet with an IP Table tab that lists all the CEN-GWEXER IP-IDs in the program. If no takeoff is provided, then the processor's IP table can be checked by running the ##ipt -t ##command from the processor after the configuration is loaded. DIN-CENCN-2's will typically have IP-IDs in the "##Cx##" range.
7 +For SHOWRUNNER™ installations, the IP address of the CEN-GWEXER does not matter as long as it is in the same range as the processor and does not conflict with any other devices on the network. Instead, CEN-GWEXERs are identified to the processor via their IP-ID. Note that which infinetEX devices are landed at which CEN-GWEXER matters, and if devices are moved between CEN-GWEXERs then the configuration will need to be updated (see below). Chief Integrations typically provides an SRTakeoff.xlsx spreadsheet with an IP Table tab that lists all the CEN-GWEXER IP-IDs in the program. If no takeoff is provided, then the processor's IP table can be checked by running the ##ipt -t ##command from the processor after the configuration is loaded. CEN-GWEXERs will typically have IP-IDs in the "##Cx##" range.
8 8  
9 9  = IP Configuration =
10 10  
... ... @@ -50,6 +50,8 @@
50 50  * At this point, it is a good idea to [[update the device firmware>>doc:SHOWRUNNER™ Setup Guide.SHOWRUNNER™ Installation Guide.SHOWRUNNER™ Installation and Network Setup.Updating Firmware.WebHome]]
51 51  * Repeat for all CEN-GWEXERs on the job
52 52  
53 +If setup has been done correctly and the ShowRunnerCLC™ program and configuration have already been loaded to the processor, then you should see the CEN-GWEXER's IP-ID reporting online when you run the ##ipt## command on both the CEN-IO and the processor.
54 +
53 53  == Static Configuration ==
54 54  
55 55  (% class="box warningmessage" %)
... ... @@ -72,6 +72,8 @@
72 72  * At this point, it is a good idea to [[update the device firmware>>doc:SHOWRUNNER™ Setup Guide.SHOWRUNNER™ Installation Guide.SHOWRUNNER™ Installation and Network Setup.Updating Firmware.WebHome]]
73 73  * Repeat for all CEN-GWEXERs on the job
74 74  
77 +If setup has been done correctly and the ShowRunnerCLC™ program and configuration have already been loaded to the processor, then you should see the CEN-GWEXER's IP-ID reporting online when you run the ##ipt## command on both the CEN-IO and the processor.
78 +
75 75  = RF Channel =
76 76  
77 77  Crestron wireless devices have 16 non-overlapping channels numbered 11-26 to prevent and avoid RF interference either from other appliances in the building (such as microwaves or Wi-Fi routers) or from other Crestron devices that are attempting to communicate with different CEN-GWEXERs.