Skip to Content

Changes for page Crestron RF Gateway Setup

Last modified by Alexander Mott on 2025/03/12 17:16
From version 2.3
edited by Alexander Mott
on 2023/12/04 16:52
Change comment: There is no comment for this version
To version 2.1
edited by Alexander Mott
on 2023/07/10 14:55
Change comment: There is no comment for this version

Summary

Details

Page properties
Title
... ... @@ -1,1 +1,1 @@
1 -CEN-GWEXER Setup
1 +*CEN-GWEXER Setup
Content
... ... @@ -2,30 +2,28 @@
2 2  {{toc/}}
3 3  {{/box}}
4 4  
5 -CEN-GWEXERs are a two-way radiofrequency (RF) transceivers that allow Crestron infinetEX and Extended Range wireless devices to communicate with the control processor over Ethernet. They are for Crestron wireless systems what [[DIN-CENCN-2s>>doc:SHOWRUNNER™ Setup Guide.SHOWRUNNER™ Installation Guide.SHOWRUNNER™ Installation and Network Setup.DIN-CENCN-2 Setup.WebHome]] are for wired Cresnet systems.
5 +Lorem ipsum dolor sit amet, consectetur adipiscing elit, sed do eiusmod tempor incididunt ut labore et dolore magna aliqua. Ut enim ad minim veniam, quis nostrud exercitation ullamco laboris nisi ut aliquip ex ea commodo consequat. Duis aute irure dolor in reprehenderit in voluptate velit esse cillum dolore eu fugiat nulla pariatur. Excepteur sint occaecat cupidatat non proident, sunt in culpa qui officia deserunt mollit anim id est laborum.
6 6  
7 -For SHOWRUNNER™ installations, the IP address of the CEN-GWEXER does not matter as long as it is in the same range as the processor and does not conflict with any other devices on the network. Instead, CEN-GWEXERs are identified to the processor via their IP-ID. Note that which infinetEX devices are landed at which CEN-GWEXER matters, and if devices are moved between CEN-GWEXERs then the configuration will need to be updated (see below). Chief Integrations typically provides an SRTakeoff.xlsx spreadsheet with an IP Table tab that lists all the CEN-GWEXER IP-IDs in the program. If no takeoff is provided, then the processor's IP table can be checked by running the ##ipt -t ##command from the processor after the configuration is loaded. DIN-CENCN-2's will typically have IP-IDs in the "##Cx##" range.
7 += Initial Connection =
8 8  
9 -= IP Configuration =
9 +Lorem
10 10  
11 -Lorem
11 +== IP Configuration ==
12 12  
13 -= SSL Setup =
14 -
15 15  Lorem
16 16  
17 -= RF Channel =
15 +== Sub 2 ==
18 18  
19 19  Lorem
20 20  
21 -= Useful Commands and Other Notes =
19 += Other Notes =
22 22  
23 23  Lorem
24 24  
25 -== Acquiring Devices ==
23 +== RF Channel ==
26 26  
27 27  Lorem
28 28  
29 -== Moving/Removing Devices (Unacquiring Devices) ==
27 +== Unacquiring Devices ==
30 30  
31 -When a wireless Crestron device is acquired to a new gateway using the typical acquiring process described above, it will automatically forget the previously connected gateway. The gateway itself, however, must manually "forget" the previously connected device before a newly acquired and addressed device will function correctly. This is necessary whether the originally connected device is moved or if the originally corrected device has failed and is being replaced.
29 +Lorem