Skip to Content

Changes for page Crestron RF Gateway Setup

Last modified by Alexander Mott on 2025/03/12 17:16
From version 2.1
edited by Alexander Mott
on 2023/07/10 14:55
Change comment: There is no comment for this version
To version 2.4
edited by Alexander Mott
on 2023/12/04 16:55
Change comment: There is no comment for this version

Summary

Details

Page properties
Title
... ... @@ -1,1 +1,1 @@
1 -*CEN-GWEXER Setup
1 +CEN-GWEXER Setup
Content
... ... @@ -2,28 +2,37 @@
2 2  {{toc/}}
3 3  {{/box}}
4 4  
5 -Lorem ipsum dolor sit amet, consectetur adipiscing elit, sed do eiusmod tempor incididunt ut labore et dolore magna aliqua. Ut enim ad minim veniam, quis nostrud exercitation ullamco laboris nisi ut aliquip ex ea commodo consequat. Duis aute irure dolor in reprehenderit in voluptate velit esse cillum dolore eu fugiat nulla pariatur. Excepteur sint occaecat cupidatat non proident, sunt in culpa qui officia deserunt mollit anim id est laborum.
5 +CEN-GWEXERs are a two-way radiofrequency (RF) transceivers that allow Crestron infinetEX and Extended Range wireless devices to communicate with the control processor over Ethernet. They are for Crestron wireless systems what [[DIN-CENCN-2s>>doc:SHOWRUNNER™ Setup Guide.SHOWRUNNER™ Installation Guide.SHOWRUNNER™ Installation and Network Setup.DIN-CENCN-2 Setup.WebHome]] are for wired Cresnet systems.
6 6  
7 -= Initial Connection =
7 +For SHOWRUNNER™ installations, the IP address of the CEN-GWEXER does not matter as long as it is in the same range as the processor and does not conflict with any other devices on the network. Instead, CEN-GWEXERs are identified to the processor via their IP-ID. Note that which infinetEX devices are landed at which CEN-GWEXER matters, and if devices are moved between CEN-GWEXERs then the configuration will need to be updated (see below). Chief Integrations typically provides an SRTakeoff.xlsx spreadsheet with an IP Table tab that lists all the CEN-GWEXER IP-IDs in the program. If no takeoff is provided, then the processor's IP table can be checked by running the ##ipt -t ##command from the processor after the configuration is loaded. DIN-CENCN-2's will typically have IP-IDs in the "##Cx##" range.
8 8  
9 -Lorem
9 += IP Configuration =
10 10  
11 -== IP Configuration ==
12 -
13 13  Lorem
14 14  
15 -== Sub 2 ==
13 += SSL Setup =
16 16  
17 17  Lorem
18 18  
19 -= Other Notes =
17 += RF Channel =
20 20  
21 21  Lorem
22 22  
23 -== RF Channel ==
21 += Useful Commands and Other Notes =
24 24  
25 25  Lorem
26 26  
27 -== Unacquiring Devices ==
25 +== Acquiring Devices ==
28 28  
29 29  Lorem
28 +
29 +== Moving/Removing Devices (Unacquiring Devices) ==
30 +
31 +When a wireless Crestron device is acquired to a new gateway using the typical acquiring process described above, it will automatically forget the previously connected gateway. The gateway itself, however, must manually "forget" the previously connected device before a newly acquired and addressed device will function correctly. This is necessary whether the originally connected device is moved or if the originally corrected device has failed and is being replaced.
32 +
33 +To unacquire a device from a gateway, it is necessary to run the below commands, replacing "[TSID]" with either the 4-byte hexadecimal TSID of a single device or "all" to forget all previously acquired devices:
34 +
35 +* ##unacquirebyt [TSID] 0##
36 +* ##unacquirebyt [TSID] 1##
37 +
38 +Once all of the necessary TSIDs have been unacquired, use the ##reboot## command to reboot the gateway and complete the unacquire process.