Pharos Configuration

(% class="row" %)

(((

ShowRunner™ can control DMX fixtures through several different methods, including Pharos DMX controllers. The most common Pharos controllers sold through Crestron are the Pharos LPC-1 (DIN-DMX-1UNIVERSE) and the Pharos LPC-2 (DIN-DMX-2UNIVERSE). These LPC controllers appear physically identical, but the LPC-1 shares a single universe across both DMX outputs while the LPC-2 has a separate universe for each output. ShowRunner™ uses the Pharos Controller API to send commands over Ethernet to the Pharos Controller, which then sends DMX commands to the fixtures.

= Pharos Project =

Pharos projects are created using the free Pharos Designer 2 software from Pharos Controls. When creating a project for use with ShowRunner™, ensure that API version 5.0 is selected for the project. Individual loads control from ShowRunner™ is achieved with group-level commands using the Pharos Controller API, so each Fixture Group defined in the Pharos Project should correspond to a single load in ShowRunner™. In addition to group-level commands, ShowRunner™ also supports mapping ShowRunner™ Scenes to Pharos Timelines.

12

13

The basic steps for creating a Pharos Project for use with ShowRunner™ are:

14

15

1. Open the Pharos Designer 2 software

16

1. In the top-right, click "New Project" and select the type of Pharos controller that will be the primary controller

17

1*. Crestron SKUs DIN-DMX-1UNIVERSE and DIN-DMX-2UNIVERSE both correspond to "LPC" in Pharos

18

1. Navigate to the "Project" page by clicking the Pharos logo on the left

19

1. Under the "Controller API" heading, verify that API Version 5.0 is selected

20

1. Navigate to the "Layout" page by clicking the pencil and ruler icon on the left

21

1. At the top left, click "Manage..." to edit the layout name and dimensions, modify grid settings, and upload a background image if desired

22

1. Locate the desired fixture in the Fixture Profile List on the right side of the Layout page

23

1*. Most fixtures can be controlled correctly using the generic single-channel, RGB, warm/cool, intensity/CCT, HSIC, etc. profiles

24

1*. Pharos also has a large selection of manufacturer-specific profiles which can be used instead of the generics

25

1*. Additional generic and manufacturer-specific profiles can be downloaded by clicking the cloud icon on the right, above the fixture profile list

26

1. Prior to adding fixtures to the layout, consider the following:

27

1*. ShowRunner™ uses group-level commands, so each individual load in ShowRunner™ must have a corresponding Fixture Group in Pharos

28

1*. The Pharos API limits commands to single-channel (intensity), RGB, or Intensity/CCT

29

1*. For RGBW fixtures, it may be a good idea to define them as separate RGB and W fixtures so that ShowRunner™ is able to control the white channel separately from the RGB channels

30

1*. Fixtures can belong to multiple Fixture Groups

31

1**. This allows ShowRunner™ to send different types of commands to the same fixtures

32

1**. Useful for certain situations, such as HSIC fixtures that need to be controlled as color-changing (RGB) in some situations but dynamic white (intensity/CCT) in others

33

1. Add fixtures to the layout by dragging them from the fixture profile list

34

1*. Every fixture that is added to the layout represents a unique set of DMX addresses

35

1*. Note that the fixture number is different than the fixture address, and is automatically incremented by Pharos Designer 2

36

1*. Right-clicking a fixture on the layout will allow you to "Duplicate" or create a "New Instance" of a fixture

37

1**. Duplicating a fixture creates a new fixture with the same profile and properties

38

1**. Creating a New Instance will create a new representation of the fixture without actually creating a new fixture; this allows you to have multiple fixtures represented on the layout that share the same DMX address

39

1.

40

1. When adding fixtures to the layout, keep in mind ShowRunner™ uses group-level controls

41

1*. ShowRunner™ is only able to send RGB, single-channel, and intensity/CCT commands

42

1*. Other fixture types (such as HSI, warm/cool, ICHS, etc.) still work correctly, but only RGB, single-channel, and intensity/CCT commands can be sent ot them

43

1*. RGBW fixtures should be defined as separate RGB and W fixtures so that ShowRunner™ can control the white channel separately from the RGB channels

1. adsf

Note: Due to limitations with the API, only single channel, RGB, or Intensity/CCT load types can be defined in ShowRunner™. Other fixture types are controllable, but the types of command that ShowRunner™

48

49

= Device Configuration =

50

51

= ShowRunner™ Configuration =

)))

Wiki source code of Pharos Configuration

Navigation

author	version	line-number	content
		1	{{box cssClass="floatinginfobox" title="CONTENTS"}}
		2	{{toc/}}
		3	{{/box}}
		4
		5	(% class="row" %)
		6	(((
		7	ShowRunner™ can control DMX fixtures through several different methods, including Pharos DMX controllers. The most common Pharos controllers sold through Crestron are the Pharos LPC-1 (DIN-DMX-1UNIVERSE) and the Pharos LPC-2 (DIN-DMX-2UNIVERSE). These LPC controllers appear physically identical, but the LPC-1 shares a single universe across both DMX outputs while the LPC-2 has a separate universe for each output. ShowRunner™ uses the Pharos Controller API to send commands over Ethernet to the Pharos Controller, which then sends DMX commands to the fixtures.
		8
		9	= Pharos Project =
		10
		11	Pharos projects are created using the free Pharos Designer 2 software from Pharos Controls. When creating a project for use with ShowRunner™, ensure that API version 5.0 is selected for the project. Individual loads control from ShowRunner™ is achieved with group-level commands using the Pharos Controller API, so each Fixture Group defined in the Pharos Project should correspond to a single load in ShowRunner™. In addition to group-level commands, ShowRunner™ also supports mapping ShowRunner™ Scenes to Pharos Timelines.
		12
		13	The basic steps for creating a Pharos Project for use with ShowRunner™ are:
		14
		15	1. Open the Pharos Designer 2 software
		16	1. In the top-right, click "New Project" and select the type of Pharos controller that will be the primary controller
		17	1*. Crestron SKUs DIN-DMX-1UNIVERSE and DIN-DMX-2UNIVERSE both correspond to "LPC" in Pharos
		18	1. Navigate to the "Project" page by clicking the Pharos logo on the left
		19	1. Under the "Controller API" heading, verify that API Version 5.0 is selected
		20	1. Navigate to the "Layout" page by clicking the pencil and ruler icon on the left
		21	1. At the top left, click "Manage..." to edit the layout name and dimensions, modify grid settings, and upload a background image if desired
		22	1. Locate the desired fixture in the Fixture Profile List on the right side of the Layout page
		23	1*. Most fixtures can be controlled correctly using the generic single-channel, RGB, warm/cool, intensity/CCT, HSIC, etc. profiles
		24	1*. Pharos also has a large selection of manufacturer-specific profiles which can be used instead of the generics
		25	1*. Additional generic and manufacturer-specific profiles can be downloaded by clicking the cloud icon on the right, above the fixture profile list
		26	1. Prior to adding fixtures to the layout, consider the following:
		27	1*. ShowRunner™ uses group-level commands, so each individual load in ShowRunner™ must have a corresponding Fixture Group in Pharos
		28	1*. The Pharos API limits commands to single-channel (intensity), RGB, or Intensity/CCT
		29	1*. For RGBW fixtures, it may be a good idea to define them as separate RGB and W fixtures so that ShowRunner™ is able to control the white channel separately from the RGB channels
		30	1*. Fixtures can belong to multiple Fixture Groups
		31	1**. This allows ShowRunner™ to send different types of commands to the same fixtures
		32	1**. Useful for certain situations, such as HSIC fixtures that need to be controlled as color-changing (RGB) in some situations but dynamic white (intensity/CCT) in others
		33	1. Add fixtures to the layout by dragging them from the fixture profile list
		34	1*. Every fixture that is added to the layout represents a unique set of DMX addresses
		35	1*. Note that the fixture number is different than the fixture address, and is automatically incremented by Pharos Designer 2
		36	1*. Right-clicking a fixture on the layout will allow you to "Duplicate" or create a "New Instance" of a fixture
		37	1**. Duplicating a fixture creates a new fixture with the same profile and properties
		38	1**. Creating a New Instance will create a new representation of the fixture without actually creating a new fixture; this allows you to have multiple fixtures represented on the layout that share the same DMX address
		39	1.
		40	1. When adding fixtures to the layout, keep in mind ShowRunner™ uses group-level controls
		41	1*. ShowRunner™ is only able to send RGB, single-channel, and intensity/CCT commands
		42	1*. Other fixture types (such as HSI, warm/cool, ICHS, etc.) still work correctly, but only RGB, single-channel, and intensity/CCT commands can be sent ot them
		43	1*. RGBW fixtures should be defined as separate RGB and W fixtures so that ShowRunner™ can control the white channel separately from the RGB channels
		44	1. adsf
		45
		46
		47	Note: Due to limitations with the API, only single channel, RGB, or Intensity/CCT load types can be defined in ShowRunner™. Other fixture types are controllable, but the types of command that ShowRunner™
		48
		49	= Device Configuration =
		50
		51	= ShowRunner™ Configuration =
		52
		53
		54
		55	)))