Changes for page Toolbox Basics

Last modified by Alexander Mott on 2024/03/19 21:00
From version 50.2
edited by Alexander Mott
on 2023/12/13 20:05
Change comment: (Autosaved)
To version 33.2
edited by Alexander Mott
on 2023/03/28 14:33
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -28,7 +28,7 @@
28 28  
29 29  = Connecting to Devices =
30 30  
31 -In order to connect to any lighting devices, your computer must be physically connected to the lighting device or the lighting network. Typically, this is achieved via TCP (i.e. Ethernet or WiFi) or USB (usually a USB-A to USB-B cable), though some older devices may require an RS-232 serial connection or a different USB cable.
31 +In order to connect to any lighting devices, your computer must be physically connected to the lighting device or the lighting network. Typically, this is achieved via TCP (i.e. Ethernet or WiFi) or USB (usually a USB-A to USB-B cable), though some older devices may require an RS-232 serial connection.
32 32  
33 33  Any Toolbox tool which requires connecting to a device has several buttons and fields at the lower left which relate to device connection:
34 34  
... ... @@ -84,7 +84,7 @@
84 84  1*. If the lighting network is on the building LAN, then you may need to reach out to the building's IT department for instructions on how to access the lighting network or VLAN.
85 85  1. Use a Cat 5a or Cat 6 cable to connect your laptop to the lighting network at an open port
86 86  1*. Most newer laptops will require some sort of adapter in order to connect to a Cat 5a/6 cable
87 -1. Configure your laptop's network settings ([[FAQ page>>https://wiki.chiefintegrations.com/FAQ/How%20do%20I%20change%20my%20computer%27s%20network%20settings]]) to be compatible with the lighting network:
87 +1. Configure your laptop's network settings to be compatible with the lighting network:
88 88  11. Navigate to Control Panel>Network and Internet>Network Connections
89 89  11. Locate the network adapter that is connected to the lighting network
90 90  11. Right click the network adapter and click "Properties"
... ... @@ -106,12 +106,11 @@
106 106  11*1*. You can verify this by opening the Windows Command Line tool and running "ipconfig" command to view your current adapter settings
107 107  1. Open Toolbox and then open the desired tool
108 108  1. Connect to the device:
109 -1*. If you have created an address book (see [[Export to Address Book>>doc:SHOWRUNNER™ Setup Guide.SHOWRUNNER™ Installation Guide.Preparation.Toolbox Basics.WebHome||anchor="HExporttoAddressBook"]] below), then select the device from the drop down menu
109 +1*. If you have created an address book, then select the device from the drop down menu
110 110  1*. If you have not created an address book, then you should click the Pencil Icon to open the Manual Connection Menu:
111 111  1*1. Leave the connection type as "TCP"
112 -1*1. Type in the IP address or Hostname of the device you wish to connect to
112 +1*1. Type in the IP address of the device you wish to connect to
113 113  1*1. Generally, the "Auto Detect" box should be left at "Auto Detect", though if you know what type of connection you need then you can manually change it
114 -1*1*. CEN-GWEXERs with Authentication enabled require manually setting the connection type to "TSL/SSL"
115 115  1*1. Leave Model, Hostname, and Serial fields blank
116 116  1*1. If the device has authentication enabled, expand the Advanced options and input the username and password
117 117  1*1. Click "OK"
... ... @@ -121,38 +121,11 @@
121 121  1*. If the device has just recently powered up, it may take a few minutes to completely wake up before it can be connected to
122 122  1*. If you have issues connecting, see [[Troubleshooting a Failed Connection>>doc:SHOWRUNNER™ Setup Guide.SHOWRUNNER™ Installation Guide.Preparation.Toolbox Basics.WebHome||anchor="HTroubleshootingaFailedConnection"]] below
123 123  
124 -== Troubleshooting a Failed Connection ==
125 -
126 -Sometimes, a connection attempt will fail and you will need to do some troubleshooting to figure out why exactly the connection could not be established. Toolbox will give different error messages, though sometimes it can be helpful to attempt to connect with another software such as PuTTY just in case the error message is more informative from the alternate software.
127 -
128 -"Device refused to identify"
129 -
130 -* This message typically means that the device is not online or could not be connected to
131 -* This message may also occur when a device has blocked your username or IP address due to making too many incorrect login attempts
132 -** IP addresses are blocked for 24 hours by default, but you can attempt to circumvent this block by changing your IP address and trying again
133 -** Users are blocked for 30 minutes by default, and it is only possible to circumvent this if another user has already been created, otherwise you must wait for the block to expire before connecting again
134 -** The below commands are useful if you are able to connect to the processor through some other means (specific commands may vary depending on the device):
135 -*** ##listblockedip## and ##remblockedip## commands can be used to view/unblock an IP address
136 -*** ##listlockeduser## and ##remlockeduser## commands can be used to view/unblock specific users
137 -*** ##setloginattempts## and ##setlockouttime## commands can be used to modify how many login attempts are allowed before blocking an IP address and how long an address will be blocked
138 -*** ##setuserloginattempts## and ##setuserlockouttime## commands are used to modify how many login attempts are allowed before blocking a user and how long that user will be blocked
139 -*** ##setlogoffidletime## command can be used to modify how long you can be inactive before the processor automatically logs you out
140 -
141 -"Device not found in database"
142 -
143 -* This message typically means that the version of your device database is out of date and the device being connected to is not in it. Use Crestron's MasterInstaller tool to ensure that Toolbox and all installed Crestron components are up-to-date
144 -
145 -See our FAQ for additional tips:
146 -
147 -* [[I can't connect to my processor via Ethernet?>>https://wiki.chiefintegrations.com/FAQ/I%20can%27t%20connect%20to%20my%20processor%20via%20Ethernet]]
148 -* [[I can't connect to a 4-Series processor via USB?>>https://wiki.chiefintegrations.com/FAQ/I%20can%27t%20connect%20to%204-Series%20processor%20via%20USB]]
149 -
150 -= Basic Tool Usage =
151 -
152 152  == Device Discovery Tool ==
153 153  
154 154  Crestron's Device Discovery Tool is used to "discover" any Crestron devices which are connected to your laptop. The most useful feature of the Device Discovery Tool is the ability to export all discovered devices to either a "Device Summary" text file or an Address Book. Discovered devices are listed in a scrollable list on the left side of the menu, and double clicking a discovered device will bring up additional configuration options on the right side. Below is an overview of the Device Discovery Tool UI:
155 155  
127 +
156 156  [[image:device discovery tool numbered.png]]
157 157  
158 158  1. Device Model - gives the specific model of the device type
... ... @@ -164,73 +164,28 @@
164 164  1. Discover Devices button - press this to restart the discovery process
165 165  1. Export... button - use this button to export discovered devices to either a Device Summary or Address Book (covered in more detail below)
166 166  
167 -=== Export to Address Book ===
168 -
169 -Address Books provide a convenient way to easily connect to different devices without memorizing all the different IP addresses and credentials for devices on your network. When an Address Book has been created for a job, you are able to connect to specific devices using the Note that when exporting devices to the Address Book, it is possible to add devices by either Hostname or by IP Address. On systems with a DHCP server, it is recommended to add devices by Hostname, but only after the final hostnames have been set for all devices.
170 -
171 -
172 -To generate an Address Book in Toolbox:
173 -
174 -1. Connect to the lighting network and open Device Discovery Tool in Toolbox
175 -1. The Device Discovery tool will automatically report how many Ethernet devices have been discovered
176 -1. Verify that the expected number of Ethernet devices have been discovered, including any TSWs, GLPACs, DIN-CENCN-2s, etc.
177 -1*. Note that only Crestron devices will appear in Device Discovery; non-Crestron devices (such as Pharos or Enttec DMX controllers) will not appear in Device Discovery Tool
178 -1*. If no devices are discovered, verify that your computer is connected to the network and your IP address is compatible with the network
179 -1*. If some devices are missing and you are not filtering the results, then there may be an issue with your DHCP server settings or the network wiring
180 -1. Click the "Export..." button below the list of discovered devices
181 -1*. If this button says "Address Book", then Toolbox needs to be updated
182 -1*. Ensure that you are not filtering out any devices or that you have only filtered out the devices you want to be filtered out
183 -[[image:export.png]]
184 -1. Click the Write Device Summary button and save the Device Summary to your computer
185 -1*. Though saved as a text file, the Device Summary is actually a table of comma separated values
186 -1*. Renaming DeviceSummary.txt to DeviceSummary.csv will allow it to be opened and manipulated in common spreadsheet software such as Microsoft Excel or LibreOffice Calc
187 -1**. Note that this .csv will have whitespace, so it may be beneficial to "clean" it using Excel's "=TRIM()" function
188 -
189 -To edit a previously created Address Book:
190 -
191 191  === Export to Device Summary ===
192 192  
193 -The Device Summary is an important documentation tool provided by Crestron. It is a .txt file containing a comma-separated-values of all networked devices, and is useful to capture which devices are online, what their current IP and hostname settings are, what version of firmware they are on, and their MAC address and serial number.
141 +The Device Summary is an important documentation tool provided by Crestron. It is a .txt file containing a comma-separated-values
194 194  
195 -To generate a Device Summary in Toolbox:
143 +=== Export to Address Book ===
196 196  
197 -1. Connect to the lighting network and open Device Discovery Tool in Toolbox
198 -1. The Device Discovery tool will automatically report how many Ethernet devices have been discovered
199 -1. Verify that the expected number of Ethernet devices have been discovered, including any TSWs, GLPACs, DIN-CENCN-2s, etc.
200 -1*. Note that only Crestron devices will appear in Device Discovery; non-Crestron devices (such as Pharos or Enttec DMX controllers) will not appear in Device Discovery Tool
201 -1*. If no devices are discovered, verify that your computer is connected to the network and your IP address is compatible with the network
202 -1*. If some devices are missing and you are not filtering the results, then there may be an issue with your DHCP server settings or the network wiring
203 -1. Click the "Export..." button below the list of discovered devices
204 -1*. If this button says "Address Book", then Toolbox needs to be updated
205 -1*. Ensure that you are not filtering out any devices or that you have only filtered out the devices you want to be filtered out
206 -[[image:export.png]]
207 -1. Click the Write Device Summary button and save the Device Summary to your computer
208 -1*. Though saved as a text file, the Device Summary is actually a table of comma separated values
209 -1*. Renaming DeviceSummary.txt to DeviceSummary.csv will allow it to be opened and manipulated in common spreadsheet software such as Microsoft Excel or LibreOffice Calc
210 -1**. Note that this .csv will have whitespace, so it may be beneficial to "clean" it using Excel's "=TRIM()" function
145 +Address Books are useful ways of managing multiple jobs that each have many devices.
211 211  
212 -Below is an example of a Device Summary for a fully-configured Zūm Wired job:
147 +== Troubleshooting a Failed Connection ==
213 213  
214 -* DeviceSummary.txt:
215 -[[image:https://wiki.chiefintegrations.com/download/SHOWRUNNER%E2%84%A2%20Setup%20Guide/SHOWRUNNER%E2%84%A2%20Installation%20Guide/SHOWRUNNER%E2%84%A2%20Installation%20and%20Network%20Setup/ZUMNET-JBOX%20Setup/WebHome/1655487020590-542.png?rev=1.1||alt="1655487020590-542.png"]]
216 -* DeviceSummary.csv:
217 -[[image:https://wiki.chiefintegrations.com/download/SHOWRUNNER%E2%84%A2%20Setup%20Guide/SHOWRUNNER%E2%84%A2%20Installation%20Guide/SHOWRUNNER%E2%84%A2%20Installation%20and%20Network%20Setup/ZUMNET-JBOX%20Setup/WebHome/1655487132138-904.png?rev=1.1||alt="1655487132138-904.png"]]
149 +"Device refused to identify" (also happens if too many login attempts are made with the wrong username/password)
218 218  
219 -(% class="box warningmessage" %)
220 -(((
221 -This section is under construction: please check back at a later date for more information
222 -)))
151 +"Device not found in database"
223 223  
224 -=== Text Console ===
153 += Basic Tool Usage =
225 225  
155 +== Text Console ==
156 +
226 226  == File Manager ==
227 227  
228 228  == Network Device Tree View ==
229 229  
230 -See our [[device addressing>>doc:SHOWRUNNER™ Setup Guide.SHOWRUNNER™ Installation Guide.Device Addressing.Addressing Devices from Toolbox.WebHome||anchor="HNetworkDeviceTreeView"]] page for more specific information on how to use the Network Device Tree View for device addressing purposes.
231 -
232 -== Script Manager ==
233 -
234 234  = Miscellaneous =
235 235  
236 236  == VPT COM Server ==
... ... @@ -237,7 +237,7 @@
237 237  
238 238  Whenever Toolbox is open, Toolbox also starts a separate process called the Crestron Toolbox VPT COM server. This process appears in the system tray with the following icon when active: [[image:1663630447432-699.png]]
239 239  
240 -Occasionally, something might go wrong with the VPT COM Server process which will prevent Toolbox from functioning correctly. To solve this problem, take the following steps:
167 +Occasionally, something goes wrong with the VPT COM Server process which will prevent Toolbox from functioning correctly. To solve this problem, take the following steps:
241 241  
242 242  1. Close Crestron Toolbox
243 243  1. Press CTRL+SHIFT+ESC to open Windows Task Manager
export.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.alexander\.mott@chiefintegrations\.com
Size
... ... @@ -1,1 +1,0 @@
1 -21.5 KB
Content
device discovery tool.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.alexander\.mott@chiefintegrations\.com
Size
... ... @@ -1,0 +1,1 @@
1 +190.7 KB
Content