Changes for page Toolbox Basics

Last modified by Alexander Mott on 2024/03/19 21:00

From 40.1 to 39.1 From 46.1 to 45.3

From version 45.3

edited by Alexander Mott
on 2023/12/12 22:26

Change comment: There is no comment for this version

To version 40.1

edited by Alexander Mott
on 2023/03/28 18:05

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

@@ -28,7 +28,7 @@
  = Connecting to Devices =
--In order to connect to any lighting devices, your computer must be physically connected to the lighting device or the lighting network. Typically, this is achieved via TCP (i.e. Ethernet or WiFi) or USB (usually a USB-A to USB-B cable), though some older devices may require an RS-232 serial connection or a different USB cable.
++In order to connect to any lighting devices, your computer must be physically connected to the lighting device or the lighting network. Typically, this is achieved via TCP (i.e. Ethernet or WiFi) or USB (usually a USB-A to USB-B cable), though some older devices may require an RS-232 serial connection.
  Any Toolbox tool which requires connecting to a device has several buttons and fields at the lower left which relate to device connection:
@@ -84,7 +84,7 @@
 *. If the lighting network is on the building LAN, then you may need to reach out to the building's IT department for instructions on how to access the lighting network or VLAN.
 . Use a Cat 5a or Cat 6 cable to connect your laptop to the lighting network at an open port
 *. Most newer laptops will require some sort of adapter in order to connect to a Cat 5a/6 cable
--1. Configure your laptop's network settings ([[FAQ page>>https://wiki.chiefintegrations.com/FAQ/How%20do%20I%20change%20my%20computer%27s%20network%20settings]]) to be compatible with the lighting network:
++1. Configure your laptop's network settings to be compatible with the lighting network:
 . Navigate to Control Panel>Network and Internet>Network Connections
 . Locate the network adapter that is connected to the lighting network
 . Right click the network adapter and click "Properties"
@@ -106,12 +106,11 @@
 *1*. You can verify this by opening the Windows Command Line tool and running "ipconfig" command to view your current adapter settings
 . Open Toolbox and then open the desired tool
 . Connect to the device:
--1*. If you have created an address book (see [[Export to Address Book>>doc:SHOWRUNNER™ Setup Guide.SHOWRUNNER™ Installation Guide.Preparation.Toolbox Basics.WebHome||anchor="HExporttoAddressBook"]] below), then select the device from the drop down menu
++1*. If you have created an address book, then select the device from the drop down menu
 *. If you have not created an address book, then you should click the Pencil Icon to open the Manual Connection Menu:
 *1. Leave the connection type as "TCP"
--1*1. Type in the IP address or Hostname of the device you wish to connect to
++1*1. Type in the IP address of the device you wish to connect to
 *1. Generally, the "Auto Detect" box should be left at "Auto Detect", though if you know what type of connection you need then you can manually change it
--1*1*. CEN-GWEXERs with Authentication enabled require manually setting the connection type to "TSL/SSL"
 *1. Leave Model, Hostname, and Serial fields blank
 *1. If the device has authentication enabled, expand the Advanced options and input the username and password
 *1. Click "OK"
@@ -153,7 +153,6 @@
 . Click the Write Device Summary button and save the Device Summary to your computer
 *. Though saved as a text file, the Device Summary is actually a table of comma separated values
 *. Renaming DeviceSummary.txt to DeviceSummary.csv will allow it to be opened and manipulated in common spreadsheet software such as Microsoft Excel or LibreOffice Calc
--1**. Note that this .csv will have whitespace, so it may be beneficial to "clean" it using Excel's "=TRIM()" function
  Below is an example of a Device Summary for a fully-configured Zūm Wired job:
@@ -171,7 +171,7 @@
  Address Books are useful ways of managing multiple jobs that each have many devices.
--Note that when exporting devices to the Address Book, it is possible to add devices by either Hostname or by IP Address. On systems with a DHCP server, it is recommended to add devices by Hostname, but only after the final hostnames have been set for all devices.
++Note that when exporting devices to the Address Book, it is possible to add devices by either
  == Troubleshooting a Failed Connection ==
@@ -178,25 +178,12 @@
  "Device refused to identify"
  * This message typically means that the device is not online or could not be connected to
--* This message may also occur when a device has blocked your username or IP address due to making too many incorrect login attempts
--** IP addresses are blocked for 24 hours by default, but you can attempt to circumvent this block by changing your IP address and trying again
--** Users are blocked for 30 minutes by default, and it is only possible to circumvent this if another user has already been created, otherwise you must wait for the block to expire before connecting again
--** The below commands are useful if you are able to connect to the processor through some other means (specific commands may vary depending on the device):
--*** ##listblockedip## and ##remblockedip## commands can be used to view/unblock an IP address
--*** ##listlockeduser## and ##remlockeduser## commands can be used to view/unblock specific users
--*** ##setloginattempts## and ##setlockouttime## commands can be used to modify how many login attempts are allowed before blocking an IP address and how long an address will be blocked
--*** ##setuserloginattempts## and ##setuserlockouttime## commands are used to modify how many login attempts are allowed before blocking a user and how long that user will be blocked
--*** ##setlogoffidletime## command can be used to modify how long you can be inactive before the processor automatically logs you out
++* This message will also occur if too many login attempts are made with the incorrect username/password. When this happens, you either need to wait until your IP address is no longer blocked or change your IP address and attempt to login again.
  "Device not found in database"
--* This message typically means that the version of your device database is out of date and the device being connected to is not in it. Use Crestron's MasterInstaller tool to ensure that Toolbox and all installed Crestron components are up-to-date
++* This message typically means that the version of your device database is out of date and the device being connected to is not in it. Use Crestron's MasterInstaller tool to ensure all Crestron components are up-to-date
--See our FAQ for additional tips:
--
--* [[I can't connect to my processor via Ethernet?>>https://wiki.chiefintegrations.com/FAQ/I%20can%27t%20connect%20to%20my%20processor%20via%20Ethernet]]
--* [[I can't connect to a 4-Series processor via USB?>>https://wiki.chiefintegrations.com/FAQ/I%20can%27t%20connect%20to%204-Series%20processor%20via%20USB]]
--
  = Basic Tool Usage =
  (% class="box warningmessage" %)
@@ -208,8 +208,6 @@
  == File Manager ==
--== Script Manager ==
--
  == Network Device Tree View ==
  = Miscellaneous =
@@ -218,7 +218,7 @@
  Whenever Toolbox is open, Toolbox also starts a separate process called the Crestron Toolbox VPT COM server. This process appears in the system tray with the following icon when active: [[image:1663630447432-699.png]]
--Occasionally, something might go wrong with the VPT COM Server process which will prevent Toolbox from functioning correctly. To solve this problem, take the following steps:
++Occasionally, something goes wrong with the VPT COM Server process which will prevent Toolbox from functioning correctly. To solve this problem, take the following steps:
 . Close Crestron Toolbox
 . Press CTRL+SHIFT+ESC to open Windows Task Manager