Changes for page Toolbox Basics

Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -28,7 +28,7 @@
28	28
29	29	= Connecting to Devices =
30	30
31		-In order to connect to any lighting devices, your computer must be physically connected to the lighting device or the lighting network. Typically, this is achieved via TCP (i.e. Ethernet or WiFi) or USB (usually a USB-A to USB-B cable), though some older devices may require an RS-232 serial connection or a different USB cable.
	31	+In order to connect to any lighting devices, your computer must be physically connected to the lighting device or the lighting network. Typically, this is achieved via TCP (i.e. Ethernet or WiFi) or USB (usually a USB-A to USB-B cable), though some older devices may require an RS-232 serial connection.
32	32
33	33	Any Toolbox tool which requires connecting to a device has several buttons and fields at the lower left which relate to device connection:
34	34
...	...	@@ -84,7 +84,7 @@
84	84	1*. If the lighting network is on the building LAN, then you may need to reach out to the building's IT department for instructions on how to access the lighting network or VLAN.
85	85	1. Use a Cat 5a or Cat 6 cable to connect your laptop to the lighting network at an open port
86	86	1*. Most newer laptops will require some sort of adapter in order to connect to a Cat 5a/6 cable
87		-1. Configure your laptop's network settings ([[FAQ page>>https://wiki.chiefintegrations.com/FAQ/How%20do%20I%20change%20my%20computer%27s%20network%20settings]]) to be compatible with the lighting network:
	87	+1. Configure your laptop's network settings to be compatible with the lighting network:
88	88	11. Navigate to Control Panel>Network and Internet>Network Connections
89	89	11. Locate the network adapter that is connected to the lighting network
90	90	11. Right click the network adapter and click "Properties"
...	...	@@ -106,12 +106,11 @@
106	106	11*1*. You can verify this by opening the Windows Command Line tool and running "ipconfig" command to view your current adapter settings
107	107	1. Open Toolbox and then open the desired tool
108	108	1. Connect to the device:
109		-1*. If you have created an address book (see [[Export to Address Book>>doc:SHOWRUNNER™ Setup Guide.SHOWRUNNER™ Installation Guide.Preparation.Toolbox Basics.WebHome||anchor="HExporttoAddressBook"]] below), then select the device from the drop down menu
	109	+1*. If you have created an address book, then select the device from the drop down menu
110	110	1*. If you have not created an address book, then you should click the Pencil Icon to open the Manual Connection Menu:
111	111	1*1. Leave the connection type as "TCP"
112		-1*1. Type in the IP address or Hostname of the device you wish to connect to
	112	+1*1. Type in the IP address of the device you wish to connect to
113	113	1*1. Generally, the "Auto Detect" box should be left at "Auto Detect", though if you know what type of connection you need then you can manually change it
114		-1*1*. CEN-GWEXERs with Authentication enabled require manually setting the connection type to "TSL/SSL"
115	115	1*1. Leave Model, Hostname, and Serial fields blank
116	116	1*1. If the device has authentication enabled, expand the Advanced options and input the username and password
117	117	1*1. Click "OK"
...	...	@@ -125,6 +125,7 @@
125	125
126	126	Crestron's Device Discovery Tool is used to "discover" any Crestron devices which are connected to your laptop. The most useful feature of the Device Discovery Tool is the ability to export all discovered devices to either a "Device Summary" text file or an Address Book. Discovered devices are listed in a scrollable list on the left side of the menu, and double clicking a discovered device will bring up additional configuration options on the right side. Below is an overview of the Device Discovery Tool UI:
127	127
	127	+
128	128	[[image:device discovery tool numbered.png]]
129	129
130	130	1. Device Model - gives the specific model of the device type
...	...	@@ -153,7 +153,6 @@
153	153	1. Click the Write Device Summary button and save the Device Summary to your computer
154	154	1*. Though saved as a text file, the Device Summary is actually a table of comma separated values
155	155	1*. Renaming DeviceSummary.txt to DeviceSummary.csv will allow it to be opened and manipulated in common spreadsheet software such as Microsoft Excel or LibreOffice Calc
156		-1**. Note that this .csv will have whitespace, so it may be beneficial to "clean" it using Excel's "=TRIM()" function
157	157
158	158	Below is an example of a Device Summary for a fully-configured Zūm Wired job:
159	159
...	...	@@ -171,7 +171,7 @@
171	171
172	172	Address Books are useful ways of managing multiple jobs that each have many devices.
173	173
174		-Note that when exporting devices to the Address Book, it is possible to add devices by either Hostname or by IP Address. On systems with a DHCP server, it is recommended to add devices by Hostname, but only after the final hostnames have been set for all devices.
	173	+Note that when exporting devices to the Address Book, it is possible to add devices by either
175	175
176	176	== Troubleshooting a Failed Connection ==
177	177
...	...	@@ -178,25 +178,12 @@
178	178	"Device refused to identify"
179	179
180	180	* This message typically means that the device is not online or could not be connected to
181		-* This message may also occur when a device has blocked your username or IP address due to making too many incorrect login attempts
182		-** IP addresses are blocked for 24 hours by default, but you can attempt to circumvent this block by changing your IP address and trying again
183		-** Users are blocked for 30 minutes by default, and it is only possible to circumvent this if another user has already been created, otherwise you must wait for the block to expire before connecting again
184		-** The below commands are useful if you are able to connect to the processor through some other means (specific commands may vary depending on the device):
185		-*** ##listblockedip## and ##remblockedip## commands can be used to view/unblock an IP address
186		-*** ##listlockeduser## and ##remlockeduser## commands can be used to view/unblock specific users
187		-*** ##setloginattempts## and ##setlockouttime## commands can be used to modify how many login attempts are allowed before blocking an IP address and how long an address will be blocked
188		-*** ##setuserloginattempts## and ##setuserlockouttime## commands are used to modify how many login attempts are allowed before blocking a user and how long that user will be blocked
189		-*** ##setlogoffidletime## command can be used to modify how long you can be inactive before the processor automatically logs you out
	180	+* This message will also occur if too many login attempts are made with the incorrect username/password. When this happens, you either need to wait until your IP address is no longer blocked or change your IP address and attempt to login again.
190	190
191	191	"Device not found in database"
192	192
193		-* This message typically means that the version of your device database is out of date and the device being connected to is not in it. Use Crestron's MasterInstaller tool to ensure that Toolbox and all installed Crestron components are up-to-date
	184	+* This message typically means that the version of your device database is out of date and the device being connected to is not in it. Use Crestron's MasterInstaller tool to ensure all Crestron components are up-to-date
194	194
195		-See our FAQ for additional tips:
196		-
197		-* [[I can't connect to my processor via Ethernet?>>https://wiki.chiefintegrations.com/FAQ/I%20can%27t%20connect%20to%20my%20processor%20via%20Ethernet]]
198		-* [[I can't connect to a 4-Series processor via USB?>>https://wiki.chiefintegrations.com/FAQ/I%20can%27t%20connect%20to%204-Series%20processor%20via%20USB]]
199		-
200	200	= Basic Tool Usage =
201	201
202	202	(% class="box warningmessage" %)
...	...	@@ -208,8 +208,6 @@
208	208
209	209	== File Manager ==
210	210
211		-== Script Manager ==
212		-
213	213	== Network Device Tree View ==
214	214
215	215	= Miscellaneous =
...	...	@@ -218,7 +218,7 @@
218	218
219	219	Whenever Toolbox is open, Toolbox also starts a separate process called the Crestron Toolbox VPT COM server. This process appears in the system tray with the following icon when active: [[image:1663630447432-699.png]]
220	220
221		-Occasionally, something might go wrong with the VPT COM Server process which will prevent Toolbox from functioning correctly. To solve this problem, take the following steps:
	205	+Occasionally, something goes wrong with the VPT COM Server process which will prevent Toolbox from functioning correctly. To solve this problem, take the following steps:
222	222
223	223	1. Close Crestron Toolbox
224	224	1. Press CTRL+SHIFT+ESC to open Windows Task Manager