Skip to Content

Changes for page Startup Checklist

Last modified by Alexander Mott on 2024/12/02 19:09
From version 5.1
edited by Scott Kohlmann
on 2023/04/20 22:44
Change comment: There is no comment for this version
To version 8.1
edited by Alexander Mott
on 2023/12/12 16:30
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.scott\.kohlmann@chiefintegrations\.com
1 +XWiki.alexander\.mott@chiefintegrations\.com
Content
... ... @@ -8,32 +8,44 @@
8 8  ** Ensure you have the [[required tools and software>>doc:SHOWRUNNER™ Setup Guide.SHOWRUNNER™ Installation Guide.Preparation.Preparing to Go On-Site.WebHome]]
9 9  ** Ensure the jobsite is meets [[site readiness requirements>>doc:SHOWRUNNER™ Setup Guide.SHOWRUNNER™ Installation Guide.Preparation.Site Readiness Checklist.WebHome]]
10 10  * Once on-site:
11 +** Configure authentication settings for networked devices
11 11  ** Configure IP settings for networked devices (processors, TSW touch panels, DIN-CENCN-2s, ZUMNET-JBOXs, GLPACs, etc.)
12 -** Configure clock and timezone for processors
13 -** Update firmware for all networked devices
14 -** If necessary, update firmware for Zūm Net and Cresnet devices
13 +** Configure clock and time zone for processors
14 +** Update firmware for all networked devices (excluding Zūm Net devices)
15 15  ** Load ShowRunnerCLC™ program, license, and configuration file to the processor
16 16  ** Load the ShowRunnerCLC™ UI to any touchscreens
17 17  ** Load the ShowRunnerCLC™ expansion program to any GLPACs
18 18  ** Configure the IP table for any required devices (TSW touch panels, DIN-CENCN-2s, ZUMNET-JBOXs, GLPACs, etc.)
19 -** Poll Cresnet and verify devices are online in Toolbox
20 -** Assign Cresnet IDs to devices and verify they are reporting online to ShowRunnerCLC™
19 +*** Ensure [[SSL Setup>>doc:SHOWRUNNER™ Setup Guide.SHOWRUNNER™ Installation Guide.SHOWRUNNER™ Installation and Network Setup.CEN-GWEXER Setup.WebHome||anchor="HSSLSetup"]] has been performed for devices that require it
20 +** Poll Cresnet/acquire infinetEX devices to gateways and verify devices are online in Toolbox
21 +** Assign Cresnet/RFID IDs to devices and verify they are reporting online to ShowRunnerCLC™
22 +** Update firmware for Zūm Net devices
23 +*** See [[Zūm Wired specific>>doc:SHOWRUNNER™ Setup Guide.SHOWRUNNER™ Installation Guide.SHOWRUNNER™ Installation and Network Setup.Updating Firmware.WebHome||anchor="HZ16BmWiredSpecificNotes"]] firmware notes
24 +** If necessary, update firmware for any Cresnet and RFID devices
21 21  ** Verify load schedule and fixture functionality
26 +*** Toggle each load individually and verify they dim and switch correctly
22 22  *** Verify loads are assigned to correct areas
23 -*** Verify loads dim and switch correctly
24 24  *** Assign friendly load labels as necessary
29 +*** Use the "Verification" checkbox to add a verified timestamp to the load
25 25  ** Verify occupancy sensors
26 26  *** Verify correct area assignments
32 +*** Verify correct direct load assignments if necessary
27 27  *** Adjust timeouts and sensitivities as necessary
28 28  ** Verify keypad functionality
29 29  *** Verify correct area assignments
30 30  *** Verify correct button layouts and functionality
37 +*** Configure keypad actions as necessary
31 31  ** Verify photocell functionality
39 +*** Verify photocells respond to changes in light levels
32 32  *** Assign photocells to appropriate lighting zones and enable for required scenes
33 33  *** Adjust sensitivity as necessary
34 34  ** Verify partition sensor functionality
35 35  *** Verify correct area assignments
36 -*** Adjust sensitivity as required
44 +*** Adjust sensitivity as required for consistent partition detection
45 +** Configure Area-level sequence of operations
46 +*** Occupancy/vacancy mode
47 +*** Occupied/vacant scenes
48 +*** Scene levels
37 37  ** Set up any schedules as required per the sequence of operations
38 38  ** Complete functionality test (QC, make sure each room functions from an end-user perspective)
39 39  ** End-user training