Last modified by Alexander Mott on 2023/12/19 00:37
From version 16.2
edited by Alexander Mott
on 2023/12/18 23:17
Change comment: (Autosaved)
To version 13.1
edited by Alexander Mott
on 2023/12/18 21:39
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -12,29 +12,6 @@
12 12  Check the currently installed version of Toolbox by navigating to Help > About Crestron Toolbox... and upgrade or downgrade your installation as necessary, or use an alternate method of addressing devices
13 13  )))
14 14  
15 -Network Device Tree View is the most user-friendly way of manually addressing devices for Crestron systems. Below is information specific to using the Network Device Tree View tool to address devices; see our [[Toolbox Basics page>>doc:SHOWRUNNER™ Setup Guide.SHOWRUNNER™ Installation Guide.Preparation.Toolbox Basics.WebHome||anchor="HNetworkDeviceTreeView"]] page for more general information on using and configuring the tool. When using the Network Device Tree View tool to address devices, keep the following in mind:
16 -
17 -*
18 -* **It is generally recommended to right-click and ensure that "Show by Device Connection" is checked.** While "Show by Category" can be useful in some situations, it is not recommended when addressing devices as it gives no indication which Net a device is connected to and may lead to accidentally misaddressing devices. "Show by Device Connection" will group devices by their connection to the host device (e.g., Cresnet devices on a DIN-CENCN-2 will be sorted by the Net that they are connected to, Zūm Wireless devices will be sorted by the ZUM-NETBRIDGE they are connected to, etc.).
19 -* In the below screenshot, all devices have already been addressed so all devices appear with the yellow circle indicating "Status: OK"
20 -* [[image:ndtv_by connection.png||height="508" width="401"]]
21 -* A new system where all devices are online but have not been re-addressed may look more like the following example, with a red exclamation point indicating duplicate Network IDs (all devices ship from the factory with the same Network ID, which inevitably leads to duplicate IDs 
22 -[[image:ndtv_all loops.png||height="503" width="404"]]
23 -** Other types of status indicator may include a black circle for "Invalid Network ID" or "Invalid/duplicate TSID or Serial Number"
24 -* Right-clicking on an individual device will give many options to resolve common issues, as well as allow for identifying a specific device:
25 -** "Refresh All" use to refresh the list of actively connected devices, necessary e.g. if a Cresnet cable has been connected/disconnected from the device
26 -*** F5 is the keyboard shortcut for this function, though in both cases it may be more reliable to completely close and reopen Network Device Tree View to ensure all devices are refreshed
27 -** "Change Network ID..." use to change the Network ID (CID) of a specific device (see our [[device addressing page>>doc:SHOWRUNNER™ Setup Guide.SHOWRUNNER™ Installation Guide.Device Addressing.Addressing Devices from Toolbox.WebHome||anchor="HNetworkDeviceTreeView"]] for more information)
28 -*** F2 is the keyboard shortcut for this function
29 -** "Identify This Device..." will put a specific device into "Identify" mode, the specific behavior for which depends on the individual device:
30 -*** Note that entering identify mode may stop the ShowRunnerCLC™ program and restart it when exiting identify mode: **to avoid losing progress and placing strain on the processor**, it is recommended to either identify and address all hardware prior to loading the ShowRunnerCLC™ program, or temporarily suspend the program with the console command ##stopprog -p:01## and then resume the program once done identifying all devices with the command ##progreset##
31 -*** Some devices will flash an LED (Cresnet keypads, GLS-SIMs, et al.)
32 -*** Some devices will flash an LED and make a noise (Cresnet occupancy sensors, most room controllers, et al.)
33 -*** Load controllers will typically flash all connected loads
34 -** "Change Serial Number..." is used to change the device's Serial Number (and thus its TSID); this is rarely required and is only necessary in cases where a device reports an invalid or duplicate SN/TSID, or where the reported SN does not match the SN physically printed on the device
35 -** "Open Text Console..." will open a Text Console window directly to the specific selected Cresnet/RFID device (//not// to the host device you are connected to in Network Device Tree View); only recommended for advanced users
36 -[[image:ndtv_rc on device.png]]
37 -
38 38  = Text Console =
39 39  
40 40  Command for processor/no nets
ndtv_all loops.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.alexander\.mott@chiefintegrations\.com
Size
... ... @@ -1,1 +1,0 @@
1 -61.4 KB
Content
ndtv_by connection.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.alexander\.mott@chiefintegrations\.com
Size
... ... @@ -1,1 +1,0 @@
1 -332.0 KB
Content