Changes for page Shades Integrations

Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -128,32 +128,22 @@
128	128	(% class="wikigeneratedid" %)
129	129	Mecho Shade's MechoNet Network Interface (MNI) allows integrating control of MechoNet hardware with third-party systems such as ShowRunnerCLC™ through a variety of different means. ShowRunnerCLC™ currently only supports using RS-232 or contact closure integrations: reach out to Chief Integrations for pricing if RS-485 or IR integrations are required.
130	130
	131	+(% class="wikigeneratedid" id="HMNIRS-232" %)
	132	+RS-232 or contact closure integration supported (reach out to Chief Integrations if RS-485 integration is required; contact closure integration is only available if Mecho wall switch ports are not being used)
	133	+
131	131	=== Hardware Requirements ===
132	132
133		-Refer to [[the above table>>doc:SHOWRUNNER™ Integrations Guide.Integration Options.Shades Integrations.WebHome||anchor="HCommonIntegrationMethods"]] for general hardware compatibility. MNI-specific details are below depending on how shades are being integrated:
	136	+Specific hardware requirements depend on which method of integration is required:
134	134
135		-* For RS-232 integration:
136		-** One RS-232 port on the ShowRunnerCLC™ system must be available for each MNI to be integrated
137		-** Depending on how the MechoNet system is designed, it may be possible to control many shades through a single RS-232 integration provided that any additional MNI and controlled MechoNet hardware is networked together and configured on the MechoNet side
138		-* For contact closure integration:
139		-** Contact closure integration utilizes the MNI switch input ports: **it is not possible to use contact closure integration if Mecho switches are installed to control the shades**
140		-** Two relays must be available for each Mecho motor to be controlled (it is possible to control multiple Mecho motors from a single relay pair provided that the MNI switch ports are wired in parallel)
141		-* For RS-485 or IR integration, reach out to Chief Integrations for potentially adding these integrations
142	142
143	143	=== Information Requirements ===
144	144
145	145	Specific information requirements depend on which method of integration is required:
146	146
147		-* **(Required)** Specify whether integration is being done through RS-232 or contact closures
	143	+* **(Required) **Whether integration is being done through RS-232 or contact closures
148	148	* For RS-232 integration:
149		-** **(Required) **MechoNet devices must be addressed so that it is possible to control them per the SOO using their Zone, Group, Node addresses
150		-*** MechoNet devices are assigned three-part Zone, Group, Node addresses similar to an IPv4 address with 3 parts instead of 4
151		-*** e.g. a ZGN address of 128.151.253 represents a device in zone 128, group 151, and node 253
152		-** **(Required) **ZGN addresses must be provided for all shades to be controlled
153		-** (Required) locat
154	154	* For contact closure integration:
155		-** **(Required)** all information specified in the [[general contact closure>>doc:SHOWRUNNER™ Integrations Guide.Integration Options.Shades Integrations.WebHome||anchor="HInformationRequirements"]] section above
156		-** **(Required)** indicate which Crestron relays correspond to each motor on each MNI, and which shades are controlled by each motor
	146	+** (Required) the same information as specified in the [[contact closure section above>>doc:SHOWRUNNER™ Integrations Guide.Integration Options.Shades Integrations.WebHome||anchor="HContactClosure%28Relays%29"]] f
157	157
158	158	== Mecho SolarTrac4 ==
159	159