Skip to Content

Changes for page Shades Integrations

Last modified by Alexander Mott on 2024/06/17 18:07
From version 9.3
edited by Alexander Mott
on 2024/06/14 23:26
Change comment: (Autosaved)
To version 2.1
edited by Alexander Mott
on 2024/06/14 21:02
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,3 +1,10 @@
1 +(% class="row" %)
2 +(((
3 +(% class="box infomessage" %)
4 +(((
5 +Note: page is under construction, check back later for updates
6 +)))
7 +
1 1  (% class="col-xs-12 col-sm-8" %)
2 2  (((
3 3  Controlling shades from ShowRunnerCLC™ is a paid feature that can be purchased either with the initial [[ShowRunnerCLC™ order>>doc:showrunner™ Order Guide.showrunner™ Additional Features.Shades.WebHome]] or added after-the-fact as an additional charge. When shades control or integration is ordered for ShowRunnerCLC™, it is vital to ensure that the BOM includes any required hardware is also ordered.
... ... @@ -10,45 +10,16 @@
10 10  
11 11  ShowRunnerCLC™ provides native support for most Crestron shade controllers as well as integration with shades controlled from third-party Crestron processors via Ethernet Inter-Systems Communication (EISC). If integration with a Crestron shades controller or system that is not detailed below is required, reach out to Chief Integrations directly to see about potentially adding support to ShowRunnerCLC™.
12 12  
13 -== Supported Hardware ==
20 +== C2N-SDC(-DC) ==
14 14  
15 -ShowRunnerCLC™ includes support for the following Crestron shade controllers:
22 +== CSA-PWS10S-HUB-ENET ==
16 16  
17 -* C2N-SDC and C2N-SDC-DC
18 -* CSC Series Controllers (discontinued)
19 -* CSA-PWS10S-HUB-ENET (controlling QMT-series motors)
20 -* DIN-2MC2
21 -* Ethernet Inter-System Communications (Crestron-to-Crestron)
24 +== DIN-2MC2 ==
22 22  
23 -For any integrations over Ethernet, the lighting network must be configured such that the lighting control processor running ShowRunnerCLC™ can communicate with all required hardware.
26 +== Ethernet Inter-Systems Communication (EISC) ==
24 24  
25 -== Information Required ==
28 += Third-Party Shade Controllers =
26 26  
27 -In order to fully define shades in the ShowRunnerCLC™ configuration, the following information must be provided by the Agent. Incomplete information will result in incomplete hardware definitions in the shipped ShowRunnerCLC™ configuration.
28 -
29 -Non-EISC shades:
30 -
31 -* **(Required)** Quantity of shade controllers
32 -* **(Required)** Quantity and location of each shade motor to be controlled
33 -** For all controllers, we must know which shade motor (i.e. window and room) is connected to each output
34 -** For systems with multiple CSA-PSW10S-HUB-ENET, we must know which HUB is the Cresnet primary
35 -
36 -EISC shades:
37 -
38 -* **(Required)** Type of EISC integration (TCP or UDP)
39 -* **(Required)** IP Address and IP-ID of non-ShowRunnerCLC™ processor
40 -* **(Required) **Joins to be used for shade control and feedback (see table below; not all features are required for all integrations)
41 -
42 -(% style="width:632px" %)
43 -|=Join|=(% style="width: 344px;" %)Description|=(% style="width: 6px;" %)Type|=(% style="width: 101px;" %)Direction
44 -|JoinOpen|(% style="width:344px" %)Sends a digital pulse when open is triggered|(% style="width:6px" %)Digital|(% style="width:101px" %)To 3rd Party
45 -|JoinClose|(% style="width:344px" %)Sends a digital pulse when close is triggered|(% style="width:6px" %)Digital|(% style="width:101px" %)To 3rd Party
46 -|JoinStop|(% style="width:344px" %)Sends a digital pulse when stop is triggered|(% style="width:6px" %)Digital|(% style="width:101px" %)To 3rd Party
47 -|JoinPosition|(% style="width:344px" %)Sends an analog value when the position is changed (0-65535 = 0-100%)|(% style="width:6px" %)Analog|(% style="width:101px" %)To 3rd Party
48 -|JoinPositionFeedback|(% style="width:344px" %)Receives an analog value for the current shade position (0-65535 = 0-100%)|(% style="width:6px" %)Analog|(% style="width:101px" %)From 3rd Party
49 -
50 -= Third-Party Shade Integrations =
51 -
52 52  ShowRunnerCLC™ supports integrating with a wide range of common shade control manufacturers, but this integration is not included in basic ShowRunnerCLC™ orders and requires the [[SR-SDN>>doc:showrunner™ Order Guide.showrunner™ Additional Features.Shades.SR-SDN.WebHome]] additional feature. If integration with a shades manufacturer or system that is not detailed below is required, reach out to Chief Integrations directly to see about potentially adding support to ShowRunnerCLC™.
53 53  
54 54  == Common Integration Methods ==
... ... @@ -67,47 +67,18 @@
67 67  * TCP/IP communication (including HTTP/HTTPS, TelNet, etc.)
68 68  ** Standard [[Ethernet wiring limitations>>doc:SHOWRUNNER™ Setup Guide.Troubleshooting Guide.Troubleshooting.Ethernet Wiring Overview.WebHome]] apply
69 69  
70 -Below is a non-exhaustive table showing which pieces of Crestron hardware have interfaces for each kind of integration (all processors are capable of TCP/IP integration provided the network has been configured correctly):
48 +Below is a table showing which pieces of Crestron hardware have interfaces for each kind of integration:
71 71  
72 -|=Hardware|=Relay Outputs|=RS-485 Serial Ports|=RS-232 Serial Ports
73 -|C2N-IO|2|✖|1
74 -|INET-IOEX-RYIO|2|✖|✖
75 -|CP3N / CP4N|8|1*|3*
76 -|DIN-IO8|8|✖|✖
77 -|DIN-AP3 / DIN-AP4|4|2*|2*
78 -|(((
79 -GLPAC-DIMFLV4-PM / GLPAC-DIMFLV8-PM
80 -(PM models only)
81 -)))|4|✖|✖
82 -|RMC3 / RMC4|2|1*|1*
83 -|ZUM-HUB4|✖|✖|✖
84 -|(% colspan="4" %)* Some serial ports are dual-purpose and can be //either// RS-485 //or// RS-232; other serial ports are //only// RS-232
50 +|=Hardware|=Relay Outputs|=RS-232 Serial Ports|=RS-485 Serial Ports
51 +|C2N-IO|2|1|✖
52 +| | | |
53 +| | | |
54 +| | | |
55 +| | | |
56 +|(% colspan="4" %)* Dual-purpose serial ports: each port can be //either// RS-232 //or// RS-485, not both simultaneously
85 85  
86 86  == Contact Closure (Relays) ==
87 87  
88 -ShowRunnerCLC™ can use output relays on Crestron hardware to control shades provided that the shades controller is capable of accepting a contact closure input for third-party control of the shades. All contact closure shade integrations are assumed to use two relays per shade zone with standard outputs as follows:
89 -
90 -* Open: close relay 1
91 -* Close: close relay 2
92 -* Stop: close both relays simultaneously
93 -
94 -Shade motors must be wired accordingly by the EC or the shades contractor (Chief Integrations technicians do not touch wiring). If the shades interfaces cannot be controlled this way, contact Chief Integrations to see about possibilities for support for shade controls using either a single relay or three or more relays per zone.
95 -
96 -=== Hardware Requirements ===
97 -
98 -* Crestron devices with output relays must be specified (refer to [[the above table>>doc:SHOWRUNNER™ Integrations Guide.Integration Options.Shades Integrations.WebHome||anchor="HCommonIntegrationMethods"]] for commonly specified hardware)
99 -* Two Crestron output relays must be available for each zone of shades to be controlled
100 -** Depending on the shade hardware and the job requirements, it may be possible to combine multiple shades to be controlled together onto a single pair of Crestron relays
101 -* It is recommended that shade interfaces be installed as close as possible to the Crestron relays controlling them to prevent issues from voltage drop or EMF interference in the wiring between the relay and the shade interface
102 -
103 -=== Information Requirements ===
104 -
105 -* **(Required)** Quantity and location of Crestron devices to be used for contact closure shade control
106 -* **(Required)** Quantity and locations of shade zones to be controlled
107 -* **(Required)** Information associating each shade zone with a relay pair
108 -** If C2N-IO or other in-field relay modules are being used, then we must know which shade(s) in which room(s) are controlled by each C2N-IO
109 -** If a processor or other in-panel modules are being used, then we must know which shade(s) in which room(s) are controlled by relays 1 & 2, which are controlled by relays 3 & 4, etc. for each module
110 -
111 111  == Draper IntelliFlex I/O A\V Gateway ==
112 112  
113 113  (% class="wikigeneratedid" %)
... ... @@ -123,34 +123,11 @@
123 123  (% class="wikigeneratedid" id="HQuantumRS-232" %)
124 124  RS-232 or TelNet integration supported
125 125  
126 -== MechoNet Network Interface (MNI) ==
75 +== MechoNet Interface (MNI) ==
127 127  
128 -(% class="wikigeneratedid" %)
129 -Mecho Shade's MechoNet Network Interface (MNI) allows integrating control of MechoNet hardware with third-party systems such as ShowRunnerCLC™ through a variety of different means. ShowRunnerCLC™ currently only supports using RS-232 or contact closure integrations: reach out to Chief Integrations for pricing if RS-485 or IR integrations are required.
77 +(% class="wikigeneratedid" id="HMNIRS-232" %)
78 +Only RS-232 integration supported
130 130  
131 -=== Hardware Requirements ===
132 -
133 -Refer to [[the above table>>doc:SHOWRUNNER™ Integrations Guide.Integration Options.Shades Integrations.WebHome||anchor="HCommonIntegrationMethods"]] for general hardware compatibility. MNI-specific details are below depending on how shades are being integrated:
134 -
135 -* For RS-232 integration:
136 -** One RS-232 port on the ShowRunnerCLC™ system must be available for each MNI to be integrated
137 -** Depending on how the MechoNet system is configured, it is possible that multiple MNI can be controlled through the RS-232 connection at a single MNI
138 -* For contact closure integration:
139 -** Contact closure integration utilizes the MNI switch input ports: **it is not possible to use contact closure integration if Mecho switches are installed to control the shades**
140 -** Two relays must be available for each Mecho motor to be controlled (it is possible to control multiple Mecho motors from a single relay pair provided that the MNI switch ports are wired in parallel)
141 -* For RS-485 or IR integration, reach out to Chief Integrations
142 -
143 -=== Information Requirements ===
144 -
145 -Specific information requirements depend on which method of integration is required:
146 -
147 -* **(Required) **Whether integration is being done through RS-232 or contact closures
148 -* For RS-232 integration:
149 -**
150 -* For contact closure integration:
151 -** **(Required)** all information specified in the [[general contact closure>>doc:SHOWRUNNER™ Integrations Guide.Integration Options.Shades Integrations.WebHome||anchor="HInformationRequirements"]] section above
152 -** **(Required)** which shades are controlled by which motor output on each MNI, and which Crestron relays those outputs are expected to correspond to
153 -
154 154  == Mecho SolarTrac4 ==
155 155  
156 156  (% class="wikigeneratedid" id="HSolarTrac4BACnet" %)
... ... @@ -182,5 +182,4 @@
182 182  {{toc/}}
183 183  {{/box}}
184 184  )))
185 -
186 -
111 +)))