Changes for page Shades Integrations

Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -2,7 +2,7 @@
2	2	(((
3	3	(% class="box infomessage" %)
4	4	(((
5		-Note: page is under construction, check back later for updates
	5	+Note: this page is currently under construction, check back later for updates
6	6	)))
7	7
8	8	(% class="col-xs-12 col-sm-8" %)
...	...	@@ -92,26 +92,28 @@
92	92
93	93	== Contact Closure (Relays) ==
94	94
95		-ShowRunnerCLC™ can use output relays on Crestron hardware to control shades provided that the shades controller is capable of accepting a contact closure input for third-party control of the shades.
	95	+ShowRunnerCLC™ can use output relays on Crestron hardware to control shades provided that the shades controller is capable of accepting a contact closure input for third-party control of the shades. All contact closure shade integrations are assumed to use two relays per shade zone with standard outputs as follows:
96	96
	97	+* Open: close relay 1
	98	+* Close: close relay 2
	99	+* Stop: close both relays simultaneously
	100	+
	101	+Shade motors must be wired accordingly by the EC or the shades contractor (Chief Integrations technicians do not touch wiring). If the shades interfaces cannot be controlled this way, contact Chief Integrations to see about possibilities for support for shade controls using either a single relay or three or more relays per zone.
	102	+
97	97	=== Hardware Requirements ===
98	98
99		-* Crestron devices with output relays must be specified (refer to table above for commonly specified hardware)
	105	+* Crestron devices with output relays must be specified (refer to [[the above table>>doc:SHOWRUNNER™ Integrations Guide.Integration Options.Shades Integrations.WebHome||anchor="HCommonIntegrationMethods"]] for commonly specified hardware)
100	100	* Two Crestron output relays must be available for each zone of shades to be controlled
101	101	** Depending on the shade hardware and the job requirements, it may be possible to combine multiple shades to be controlled together onto a single pair of Crestron relays
102		-** Contact Chief Integrations if the shades manufacturer specifies either a single or more than two contact closures for third-party integration
103		-* Standard command outputs are as follows:
104		-** Open: close relay 1
105		-** Close: close relay 2
106		-** Stop: close both relays simultaneously
107		-* It is recommended that shade interfaces be installed as close as possible to the Crestron relays controlling them to prevent issues from voltage drop or EMF in the wiring between the relay and the shade interface
	108	+* It is recommended that shade interfaces be installed as close as possible to the Crestron relays controlling them to prevent issues from voltage drop or EMF interference in the wiring between the relay and the shade interface
108	108
109	109	=== Information Requirements ===
110	110
111	111	* **(Required)** Quantity and location of Crestron devices to be used for contact closure shade control
112	112	* **(Required)** Quantity and locations of shade zones to be controlled
113		-* **(Required)** Information associating each shade zone with a pair of relays
114		-** E.g., if a CP4N is being used then we must know which shade(s) in which room(s) are controlled by relays 1 & 2, which shade(s) are controlled by relays 3 & 4, etc.
	114	+* **(Required)** Information associating each shade zone with a relay pair
	115	+** If C2N-IO or other in-field relay modules are being used, then we must know which shade(s) in which room(s) are controlled by each C2N-IO
	116	+** If a processor or other in-panel modules are being used, then we must know which shade(s) in which room(s) are controlled by relays 1 & 2, which are controlled by relays 3 & 4, etc. for each module
115	115
116	116	== Draper IntelliFlex I/O A\V Gateway ==
117	117