Changes for page Shades Integrations

Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -56,21 +56,15 @@
56	56	While most third-party shade controllers have proprietary integration protocols specific to each manufacturer and model, there are common industry standards which dictate the wiring and hardware requirements to integrate third-party shades with ShowRunnerCLC™:
57	57
58	58	* Contact closure (Relays)
59		-** Shades are controlled by ShowRunnerCLC™-controlled contact closure relays
60		-** Typically requires two relays per shade motor or collection of shade motors to be controlled (one relay for "open" and one relay for "close")
61		-** No standard specified length limitation for wiring (individual shade manufacturers may specify cabling and distance limitations)
	59	+** No standard specified length limitation (individual shade manufacturers may specify cabling and distance limitations)
62	62	** Relay control can be susceptible to voltage drop or EMF interference: it is highly recommended to locate the Crestron controlled relay as close as possible to the shades interface being controlled
63	63	* Serial RS-232
64		-** Shades are controlled by a ShowRunnerCLC™-controlled serial communications port through wiring which adheres to RS-232 specification
65	65	** 50' maximum distance per specification
66	66	** Point-to-point communication mandates a one-to-one relationship of Crestron RS-232 interfaces to shade RS-232 interfaces (i.e. there must be one RS-232 port available on the Crestron system for every RS-232 shade interface; depending on the shades design, a single shades interface may control many shades so it may be possible that a system with many shades only requires one RS-232 connection to the Crestron system)
67	67	* Serial RS-485
68		-** Shades are controlled by a ShowRunnerCLC™-controlled serial communications port through wiring which adheres to RS-485 specification
69	69	** 4000' maximum distance per specification (individual shades manufacturers may specify lower cabling and distance limitations, and real-world conditions may reduce the actual maximum distance that can be achieved before system performance is noticeably impacted)
70	70	** Multidrop communications allows for daisy-chain and star wiring topologies, up to 32 devices per Crestron RS-485 interface (shades manufacturers may specify lower device counts)
71	71	* TCP/IP communication (including HTTP/HTTPS, TelNet, etc.)
72		-** Shades are controlled by ShowRunnerCLC™ through the LAN port using standard Ethernet cabling and TCP/IP (% style="display:none" %) (%%)communications protocols(% style="display:none" %)
73		-** ShowRunnerCLC™ processor and shades interface must be able to communicate with each other, typically requiring either that the shades interface and lighting processor are  located on the same LAN/VLAN or that the building IT be involved to ensure that communications are possible between the two systems
74	74	** Standard [[Ethernet wiring limitations>>doc:SHOWRUNNER™ Setup Guide.Troubleshooting Guide.Troubleshooting.Ethernet Wiring Overview.WebHome]] apply
75	75
76	76	Below is a non-exhaustive table showing which pieces of Crestron hardware have interfaces for each kind of integration (all processors are capable of TCP/IP integration provided the network has been configured correctly):
...	...	@@ -150,16 +150,12 @@
150	150
151	151	Specific information requirements depend on which method of integration is required:
152	152
153		-* **(Required)** Specify whether integration is being done through RS-232 or contact closures
	147	+* **(Required) **Whether integration is being done through RS-232 or contact closures
154	154	* For RS-232 integration:
155		-** **(Required) **MechoNet devices must be addressed so that it is possible to control them per the SOO using their Zone, Group, Node addresses
156		-*** MechoNet devices are assigned three-part Zone, Group, Node addresses similar to an IPv4 address with 3 parts instead of 4
157		-*** e.g. a ZGN address of 128.151.253 represents a device in zone 128, group 151, and node 253
158		-** **(Required) **ZGN addresses must be provided for all shades to be controlled
159		-** **(Required)** location for each shade to be controlled so that they can be assigned to the correct areas in ShowRunnerCLC™
	149	+** (Required) whether shades are controlled by MechoNet group or by individual shade address
160	160	* For contact closure integration:
161	161	** **(Required)** all information specified in the [[general contact closure>>doc:SHOWRUNNER™ Integrations Guide.Integration Options.Shades Integrations.WebHome||anchor="HInformationRequirements"]] section above
162		-** **(Required)** indicate which Crestron relays correspond to each motor on each MNI, and which shades are controlled by each motor
	152	+** **(Required)** which shades are controlled by which motor output on each MNI, and which Crestron relays those outputs are expected to correspond to
163	163
164	164	== Mecho SolarTrac4 ==
165	165