Wiki source code of *ZUMNET-JBOX Load Controllers
Version 37.1 by Alexander Mott on 2022/06/10 15:34
Show last authors
author | version | line-number | content |
---|---|---|---|
1 | {{box title="**Contents**"}} | ||
2 | {{toc/}} | ||
3 | {{/box}} | ||
4 | |||
5 | (% class="row" %) | ||
6 | ((( | ||
7 | (% class="col-xs-12 col-sm-8" %) | ||
8 | ((( | ||
9 | = Zūm Net JBOX Devices = | ||
10 | |||
11 | ZUMNET-JBOX devices are distributed lighting controllers that comprise the networked portion of a Zūm Wired system. Typically, each room will have just one ZUMNET-JBOX device that connects to the [[Zūm Net>>SHOWRUNNER™ Setup Guide.Wiring Guide.Wiring Overview.Zūm Net.WebHome||anchor="HZ16BmNet"]] lighting network and may optionally host one or more [[Zūm Link>>SHOWRUNNER™ Setup Guide.Wiring Guide.Wiring Overview.Zūm Net.WebHome||anchor="HZ16BmLink"]] devices. | ||
12 | |||
13 | All ZUMNET-JBOXs have two purple ZUMNET (LAN) ports and two orange ZUMLINK (ROOM) ports: | ||
14 | |||
15 | * One ZUMNET (LAN) port should come from the previous Zūm Net device or a Hub panel | ||
16 | * One ZUMNET (LAN) port should go to the next Zūm Net device or remain unused | ||
17 | * One ZUMLINK (ROOM) port should go to the first Zūm Link device on the first Zūm Link run | ||
18 | * One ZUMLINK (ROOM) port should go to the first Zūm Link device on the second Zūm Link run | ||
19 | |||
20 | It is important to note that while there are two ZUMLINK ports, Zūm Link runs should never be looped back to a ZUMNET-JBOX. Zūm Link runs should originate at a ZUMNET-JBOX, connect to a number of Zūm Link devices, and then stop at the last Zūm Link device. The reason for having multiple ZUMLINK ports is ease of installation; for example, if there are two ZUMLINK-KP keypads in a room, it might be easier to put them at the end of two separate runs so that only one RJ-45 terminated Zūm Link cable needs to be pulled through conduit. | ||
21 | |||
22 | In //[[Figure 1>>WebHome||anchor="HFigure1"]]//, ZUMLINK ports are shown in orange, ZUMNET ports are shown in purple, and the sensor input block is between them. | ||
23 | |||
24 | == ZUMNET-JBOX-16A-LV Wiring == | ||
25 | |||
26 | The ZUMNET-JBOX-16A-LV attaches to a standard 4" or 4-11/16" junction box through a 1/2" knockout. High voltage AC and 0-10V dimming splices are made inside of the junction box, while low-voltage Zūm Net, Zūm Link, and non-system sensor connections are made outside of the junction box. | ||
27 | //[[Figure 2>>WebHome||anchor="HFigure2"]]// | ||
28 | |||
29 | The official quick start guide from Crestron is available [[here>>attach:mg_qs_zumnet-jbox.pdf]]. | ||
30 | |||
31 | == ZUMNET-JBOX-DALI Wiring == | ||
32 | |||
33 | L | ||
34 | //[[Figure 3>>WebHome||anchor="HFigure3"]]// | ||
35 | |||
36 | The official quick start guide from Crestron is available [[here>>attach:mg_qs_zumnet-jbox.pdf]]. | ||
37 | |||
38 | == Sensor Input Wiring Detail == | ||
39 | |||
40 | Non-system sensors (including Crestron GLS-ODT-C-NS sensors, GLA-LDL photocells, and Steinel occupancy sensors) may be landed at the sensor input terminal block of ZUMNET-JBOX devices. Details on the sensor input wiring can be found [[here>>doc:SHOWRUNNER™ Setup Guide.Wiring Guide.Zūm Wired System Overview.Sensor Input Detail (ZUMNET- and ZUMLINK-JBOX).WebHome]]. | ||
41 | ))) | ||
42 | |||
43 | |||
44 | (% class="col-xs-12 col-sm-4" %) | ||
45 | ((( | ||
46 | (% class="wikigeneratedid" id="HFigure1" %) | ||
47 | ((( | ||
48 | [[[[image:wiki_znet over trans.png]]>>attach:wiki_znet over trans.png]] | ||
49 | //Figure 1: ZUMNET-JBOX Overview [[(larger)>>https://wiki.chiefintegrations.com/download/Wiring%20Guide/Z%C5%ABm%20Wired%20System%20Overview/Load%20Controllers%20%28ZUMNET-JBOX%29/WebHome/wiki_znet%20over%20trans.png?rev=1.1]]// | ||
50 | ))) | ||
51 | |||
52 | (% class="wikigeneratedid" id="HFigure2" %) | ||
53 | ((( | ||
54 | [[[[image:wiki_znetlv trans.png]]>>attach:wiki_znetlv trans.png]] | ||
55 | //Figure 2: ZUMNET-JBOX-16A-LV Wiring [[(larger)>>https://wiki.chiefintegrations.com/download/Wiring%20Guide/Z%C5%ABm%20Wired%20System%20Overview/Load%20Controllers%20%28ZUMNET-JBOX%29/WebHome/wiki_znetlv%20trans.png?rev=1.1]]// | ||
56 | ))) | ||
57 | |||
58 | (% class="wikigeneratedid" id="HFigure3" %) | ||
59 | ((( | ||
60 | [[[[image:wiki_znetdali trans.png]]>>attach:wiki_znetdali trans.png]] | ||
61 | //Figure 3: ZUMNET-JBOX-DALI Wiring [[(larger)>>https://wiki.chiefintegrations.com/download/Wiring%20Guide/Z%C5%ABm%20Wired%20System%20Overview/Load%20Controllers%20%28ZUMNET-JBOX%29/WebHome/wiki_znetdali%20trans.png?rev=1.1]]// | ||
62 | ))) | ||
63 | ))) | ||
64 | ))) |