Wiki source code of ZUMNET-JBOX Load Controllers
Version 33.1 by Alexander Mott on 2022/03/30 16:17
Hide last authors
| author | version | line-number | content |
|---|---|---|---|
 |
4.2 | 1 | {{box title="**Contents**"}} |
| 2 | {{toc/}} | ||
| 3 | {{/box}} | ||
| 4 | |||
| |
1.1 | 5 | (% class="row" %) |
| 6 | ((( | ||
| 7 | (% class="col-xs-12 col-sm-8" %) | ||
| 8 | ((( | ||
| |
5.1 | 9 | = Zūm Net JBOX Devices = |
| |
1.1 | 10 | |
| |
32.1 | 11 | ZUMNET-JBOX devices are distributed lighting controllers that comprise the networked portion of a Zūm Wired system. Typically, each room will have just one ZUMNET-JBOX device that connects to the [[Zūm Net>>SHOWRUNNER™ Setup Guide.Wiring Guide.Wiring Overview.Zūm Net.WebHome||anchor="HZ16BmNet"]] lighting network and may optionally host one or more [[Zūm Link>>SHOWRUNNER™ Setup Guide.Wiring Guide.Wiring Overview.Zūm Net.WebHome||anchor="HZ16BmLink"]] devices. |
| |
9.1 | 12 | |
| |
13.1 | 13 | All ZUMNET-JBOXs have two purple ZUMNET (LAN) ports and two orange ZUMLINK (ROOM) ports: |
| |
1.1 | 14 | |
| |
13.1 | 15 | * One ZUMNET (LAN) port should come from the previous Zūm Net device or a Hub panel |
| |
20.1 | 16 | * One ZUMNET (LAN) port should go to the next Zūm Net device or remain unused |
| |
13.1 | 17 | * One ZUMLINK (ROOM) port should go to the first Zūm Link device on the first Zūm Link run |
| 18 | * One ZUMLINK (ROOM) port should go to the first Zūm Link device on the second Zūm Link run | ||
| 19 | |||
| 20 | It is important to note that while there are two ZUMLINK ports, Zūm Link runs should never be looped back to a ZUMNET-JBOX. Zūm Link runs should originate at a ZUMNET-JBOX, connect to a number of Zūm Link devices, and then stop at the last Zūm Link device. The reason for having multiple ZUMLINK ports is ease of installation; for example, if there are two ZUMLINK-KP keypads in a room, it might be easier to put them at the end of two separate runs so that only one RJ-45 terminated Zūm Link cable needs to be pulled through conduit. | ||
| 21 | |||
| |
17.1 | 22 | In //[[Figure 1>>xwiki:Wiring Guide.Zūm Wired System Overview.Load Controllers (ZUMNET-JBOX).WebHome||anchor="HFigure1"]]//, ZUMLINK ports are shown in orange, ZUMNET ports are shown in purple, and the sensor input block is between them. |
| |
16.1 | 23 | |
| |
5.1 | 24 | == ZUMNET-JBOX-16A-LV Wiring == |
| |
1.1 | 25 | |
| |
31.1 | 26 | The ZUMNET-JBOX-16A-LV attaches to a standard 4" or 4-11/16" junction box through a 1/2" knockout. High voltage AC and 0-10V dimming splices are made inside of the junction box, while low-voltage Zūm Net, Zūm Link, and non-system sensor connections are made outside of the junction box. |
| |
29.1 | 27 | //[[Figure 2>>xwiki:Wiring Guide.Zūm Wired System Overview.Load Controllers (ZUMNET-JBOX).WebHome||anchor="HFigure2"]]// |
| |
1.1 | 28 | |
| |
21.1 | 29 | The official quick start guide from Crestron is available [[here>>attach:mg_qs_zumnet-jbox.pdf]]. |
| |
13.1 | 30 | |
| |
5.1 | 31 | == ZUMNET-JBOX-DALI Wiring == |
| |
1.1 | 32 | |
| |
29.1 | 33 | L |
| 34 | //[[Figure 3>>xwiki:Wiring Guide.Zūm Wired System Overview.Load Controllers (ZUMNET-JBOX).WebHome||anchor="HFigure3"]]// | ||
| |
1.1 | 35 | |
| |
21.1 | 36 | The official quick start guide from Crestron is available [[here>>attach:mg_qs_zumnet-jbox.pdf]]. |
| |
13.1 | 37 | |
| |
5.1 | 38 | == Sensor Input Wiring Detail == |
| |
1.1 | 39 | |
| |
18.1 | 40 | Non-system sensors (including Crestron GLS-ODT-C-NS sensors, GLA-LDL photocells, and Steinel occupancy sensors) may be landed at the sensor input terminal block of ZUMNET-JBOX devices. Details on the sensor input wiring can be found [[here>>doc:Wiring Guide.Zūm Wired System Overview.Sensor Input Detail (ZUMNET- and ZUMLINK-JBOX).WebHome]]. |
| |
1.1 | 41 | ))) |
| 42 | |||
| 43 | |||
| 44 | (% class="col-xs-12 col-sm-4" %) | ||
| 45 | ((( | ||
| |
16.1 | 46 | (% class="wikigeneratedid" id="HFigure1" %) |
| 47 | ((( | ||
| |
27.1 | 48 | [[[[image:wiki_znet over trans.png]]>>attach:wiki_znet over trans.png]] |
| |
16.1 | 49 | //Figure 1: ZUMNET-JBOX Overview [[(larger)>>https://wiki.chiefintegrations.com/download/Wiring%20Guide/Z%C5%ABm%20Wired%20System%20Overview/Load%20Controllers%20%28ZUMNET-JBOX%29/WebHome/wiki_znet%20over%20trans.png?rev=1.1]]// |
| |
29.1 | 50 | ))) |
| 51 | |||
| |
28.1 | 52 | (% class="wikigeneratedid" id="HFigure2" %) |
| 53 | ((( | ||
| |
27.1 | 54 | [[[[image:wiki_znetlv trans.png]]>>attach:wiki_znetlv trans.png]] |
| 55 | //Figure 2: ZUMNET-JBOX-16A-LV Wiring [[(larger)>>https://wiki.chiefintegrations.com/download/Wiring%20Guide/Z%C5%ABm%20Wired%20System%20Overview/Load%20Controllers%20%28ZUMNET-JBOX%29/WebHome/wiki_znetlv%20trans.png?rev=1.1]]// | ||
| |
28.1 | 56 | ))) |
| |
29.1 | 57 | |
| |
28.1 | 58 | (% class="wikigeneratedid" id="HFigure3" %) |
| 59 | ((( | ||
| |
27.1 | 60 | [[[[image:wiki_znetdali trans.png]]>>attach:wiki_znetdali trans.png]] |
| 61 | //Figure 3: ZUMNET-JBOX-DALI Wiring [[(larger)>>https://wiki.chiefintegrations.com/download/Wiring%20Guide/Z%C5%ABm%20Wired%20System%20Overview/Load%20Controllers%20%28ZUMNET-JBOX%29/WebHome/wiki_znetdali%20trans.png?rev=1.1]]// | ||
| |
1.1 | 62 | ))) |
| 63 | ))) | ||
| |
16.1 | 64 | ))) |