Skip to Content
Last modified by Alexander Mott on 2024/01/05 18:55
From version 33.2
edited by Alexander Mott
on 2022/03/30 16:17
Change comment: Update document after refactoring.
To version 36.1
edited by Alexander Mott
on 2022/03/30 17:02
Change comment: There is no comment for this version

Summary

Details

Page properties
Title
... ... @@ -1,1 +1,1 @@
1 -ZUMNET-JBOX Load Controllers
1 +*ZUMNET-JBOX Load Controllers
Content
... ... @@ -19,12 +19,12 @@
19 19  
20 20  It is important to note that while there are two ZUMLINK ports, Zūm Link runs should never be looped back to a ZUMNET-JBOX. Zūm Link runs should originate at a ZUMNET-JBOX, connect to a number of Zūm Link devices, and then stop at the last Zūm Link device. The reason for having multiple ZUMLINK ports is ease of installation; for example, if there are two ZUMLINK-KP keypads in a room, it might be easier to put them at the end of two separate runs so that only one RJ-45 terminated Zūm Link cable needs to be pulled through conduit.
21 21  
22 -In //[[Figure 1>>xwiki:Wiring Guide.Zūm Wired System Overview.Load Controllers (ZUMNET-JBOX).WebHome||anchor="HFigure1"]]//, ZUMLINK ports are shown in orange, ZUMNET ports are shown in purple, and the sensor input block is between them.
22 +In //[[Figure 1>>WebHome||anchor="HFigure1"]]//, ZUMLINK ports are shown in orange, ZUMNET ports are shown in purple, and the sensor input block is between them.
23 23  
24 24  == ZUMNET-JBOX-16A-LV Wiring ==
25 25  
26 26  The ZUMNET-JBOX-16A-LV attaches to a standard 4" or 4-11/16" junction box through a 1/2" knockout. High voltage AC and 0-10V dimming splices are made inside of the junction box, while low-voltage Zūm Net, Zūm Link, and non-system sensor connections are made outside of the junction box.
27 -//[[Figure 2>>xwiki:Wiring Guide.Zūm Wired System Overview.Load Controllers (ZUMNET-JBOX).WebHome||anchor="HFigure2"]]//
27 +//[[Figure 2>>WebHome||anchor="HFigure2"]]//
28 28  
29 29  The official quick start guide from Crestron is available [[here>>attach:mg_qs_zumnet-jbox.pdf]].
30 30  
... ... @@ -31,13 +31,13 @@
31 31  == ZUMNET-JBOX-DALI Wiring ==
32 32  
33 33  L
34 -//[[Figure 3>>xwiki:Wiring Guide.Zūm Wired System Overview.Load Controllers (ZUMNET-JBOX).WebHome||anchor="HFigure3"]]//
34 +//[[Figure 3>>WebHome||anchor="HFigure3"]]//
35 35  
36 36  The official quick start guide from Crestron is available [[here>>attach:mg_qs_zumnet-jbox.pdf]].
37 37  
38 38  == Sensor Input Wiring Detail ==
39 39  
40 -Non-system sensors (including Crestron GLS-ODT-C-NS sensors, GLA-LDL photocells, and Steinel occupancy sensors) may be landed at the sensor input terminal block of ZUMNET-JBOX devices. Details on the sensor input wiring can be found [[here>>doc:Wiring Guide.Zūm Wired System Overview.Sensor Input Detail (ZUMNET- and ZUMLINK-JBOX).WebHome]].
40 +Non-system sensors (including Crestron GLS-ODT-C-NS sensors, GLA-LDL photocells, and Steinel occupancy sensors) may be landed at the sensor input terminal block of ZUMNET-JBOX devices. Details on the sensor input wiring can be found [[here>>doc:SHOWRUNNER™ Setup Guide.Wiring Guide.Zūm Wired System Overview.Sensor Input Detail (ZUMNET- and ZUMLINK-JBOX).WebHome]].
41 41  )))
42 42  
43 43