Wiki source code of GLS-SIM
Version 5.1 by Alexander Mott on 2022/10/17 20:46
Hide last authors
| author | version | line-number | content |
|---|---|---|---|
 |
1.1 | 1 | (% class="row" %) |
| 2 | ((( | ||
| 3 | (% class="col-xs-12 col-sm-8" %) | ||
| 4 | ((( | ||
| |
3.1 | 5 | (% class="box warningmessage" %) |
| 6 | ((( | ||
| 7 | Note: GLS-SIM come with two dials labeled "HI" and "LO" which are used for setting the GLS-SIM's network address. These dials should be left at the factory "00" position unless specifically instructed to change them - if these dials are set to anything else then the address for the GLS-SIM cannot be changed via software and is only able to be changed using the dials. | ||
| 8 | ))) | ||
| 9 | |||
| |
1.1 | 10 | Lorem |
| 11 | |||
| 12 | See //[[Figure 1>>WebHome||anchor="HFigure1"]]// for details. | ||
| |
2.1 | 13 | See //[[Figure 2>>WebHome||anchor="HFigure2"]]// for details. |
| |
1.1 | 14 | |
| 15 | = Device Wiring = | ||
| 16 | |||
| |
5.1 | 17 | GLS-SIMs have two distinct sensor ports, allowing for up to two distinct inputs on each GLS-SIM. Inputs can come from any number of devices, including occupancy sensors, photocells, key switches, and contact closures. |
| |
1.1 | 18 | |
| 19 | == Occupancy Sensor == | ||
| 20 | |||
| |
5.1 | 21 | All occupancy sensors to be used with a GLS-SIM must be a "non-system" sensor. Cresnet or ZUMLINK sensors should be connected via Cresnet or ZUMLINK instead of the sensor port of a GLS-SIM. |
| |
1.1 | 22 | |
| |
2.1 | 23 | == Photocell (Daylight Sensor) == |
| |
1.1 | 24 | |
| 25 | Lorem | ||
| 26 | |||
| |
2.2 | 27 | == Key Switch == |
| |
1.1 | 28 | |
| |
5.1 | 29 | There are two primary kinds of key switches: momentary and maintained. In addition to official Crestron key switches, there are third party manufacturers of key switches and buttons which can be used as inputs for a GLS-SIM. |
| |
1.1 | 30 | |
| |
5.1 | 31 | === Crestron Momentary === |
| |
2.1 | 32 | |
| |
5.1 | 33 | ==== ==== |
| |
2.1 | 34 | |
| |
5.1 | 35 | === Crestron Maintained === |
| 36 | |||
| 37 | Note: feedback is not available on maintained key switches, since the feedback status of the switch is apparant from the position of the key. | ||
| 38 | |||
| 39 | === Other Manufacturers === | ||
| 40 | |||
| 41 | |||
| |
3.1 | 42 | = DIP Switches = |
| |
1.1 | 43 | |
| |
3.1 | 44 | Every GLS-SIM has four DIP switches which can be used to adjust the behavior and function of the two sensor ports on the GLS-SIM. For every DIP switch, the "up" position corresponds to "on", while the "down" position corresponds to "off". Switches 1 and 2 correspond to sensor port 1, while switches 2 and 3 correspond to sensor port 2. |
| |
2.2 | 45 | |
| |
3.1 | 46 | The table below covers the function of each of the DIP switches and their affect on the GLS-SIM. |
| |
2.2 | 47 | |
| 48 | (% class="table-condensed" %) | ||
| 49 | |(% style="width:50px" %)**Port**|(% style="width:92px" %)**DIP Switch**|(% style="width:85px" %)**Setting**|(% style="width:757px" %)**Result** | ||
| 50 | |(% rowspan="4" style="width:50px" %)1|(% rowspan="2" style="width:92px" %)1|(% style="width:85px" %)On (Up)|(% style="width:757px" %)Disables pull-up resistor for port 1 | ||
| 51 | |(% style="width:85px" %)Off (Down)|(% style="width:757px" %)Enables pull-up resistor on port 1 (port 1 will output 5V) | ||
| 52 | |(% rowspan="2" style="width:92px" %)2|(% style="width:85px" %)On (Up)|(% style="width:757px" %)Normal polarity (high input reads as "true") | ||
| 53 | |(% style="width:85px" %)Off (Down)|(% style="width:757px" %)Inverted polarity (high input reads as "false") | ||
| 54 | |(% rowspan="4" style="width:50px" %)2|(% rowspan="2" style="width:92px" %)3|(% style="width:85px" %)On (Up)|(% style="width:757px" %)Disables pull-up resistor for port 2 | ||
| 55 | |(% style="width:85px" %)Off (Down)|(% style="width:757px" %)Enables pull-up resistor on port 2 (port 2 will output 5V) | ||
| 56 | |(% rowspan="2" style="width:92px" %)4|(% style="width:85px" %)On (Up)|(% style="width:757px" %)Normal polarity (high input reads as "true") | ||
| 57 | |(% style="width:85px" %)Off (Down)|(% style="width:757px" %)Inverted polarity (high input reads as "false") | ||
| 58 | |||
| 59 | == Occupancy Sensor == | ||
| 60 | |||
| |
1.1 | 61 | Lorem |
| 62 | |||
| |
2.2 | 63 | == Photocell (Daylight Sensor) == |
| |
1.1 | 64 | |
| 65 | Lorem | ||
| 66 | |||
| |
2.2 | 67 | == Key Switch == |
| |
1.1 | 68 | |
| 69 | Lorem | ||
| 70 | |||
| 71 | = Troubleshooting = | ||
| |
3.1 | 72 | |
| 73 | |||
| |
1.1 | 74 | ))) |
| 75 | |||
| 76 | |||
| 77 | (% class="col-xs-12 col-sm-4" %) | ||
| 78 | ((( | ||
| 79 | {{box title="**CONTENTS**"}} | ||
| 80 | {{toc/}} | ||
| 81 | {{/box}} | ||
| 82 | |||
| 83 | (% class="wikigeneratedid" id="HFigure1" %) | ||
| 84 | ((( | ||
| 85 | [[image:Templates.Article.Template.WebHome@image1.jpg]] | ||
| 86 | //Figure 1: [[Sea>>https://commons.wikimedia.org/wiki/File:Isle_of_Icacos_II.jpg]]// | ||
| 87 | ))) | ||
| 88 | |||
| 89 | (% class="wikigeneratedid" id="HFigure2" %) | ||
| 90 | ((( | ||
| 91 | [[image:Templates.Article.Template.WebHome@image2.jpg]] | ||
| 92 | //Figure 2: [[Waves>>https://commons.wikimedia.org/wiki/File:Culebra_-_Playa_de_Flamenco.jpg]]// | ||
| 93 | ))) | ||
| 94 | ))) | ||
| 95 | ))) |