Skip to Content

Changes for page Crestron Command Line

Last modified by Craig Lewis on 2022/11/14 15:09
From version 9.3
edited by Craig Lewis
on 2022/09/19 18:28
Change comment: Update document after refactoring.
To version 1.1
edited by Craig Lewis
on 2021/07/12 17:20
Change comment: There is no comment for this version

Summary

Details

Page properties
Parent
... ... @@ -1,1 +1,1 @@
1 -SHOWRUNNER™ Setup Guide.Troubleshooting Guide.Advanced Tools.WebHome
1 +SHOWRUNNER™ User Guide & Wiki.Troubleshooting.WebHome
Content
... ... @@ -1,75 +1,9 @@
1 -__**Frequently used commands:**__
1 +Est - shows IP Configurations of connected device
2 2  
3 -BROADcast Operator Enable Error Broadcast
3 +DHCP 0 off - turns DHCP off and allows users to set static IP Address
4 4  
5 -ERR SYS  Operator Prints the error log
5 +IPA 0 x.x.x.x - to set static IP Address
6 6  
7 -SHOWLICENSE Operator Display list of licensed application(s)
7 +IP 0 x.x.x.0 - to set IP Mask (typical mask is 255.255.255.0)
8 8  
9 -SHOWLICENSEEX Operator Display list of licensed application(s)
10 -
11 -SYSTEMKEY Administrator Display system key.
12 -
13 -GETCODE Operator Retrieve code needed for eControl2 activation
14 -
15 -Autodiscovery Query - scans network for all connected Crestron network devices
16 -
17 -VERsion Operator Version Command
18 -
19 -EST- shows IP Configurations of connected device (same command as ipconfig)
20 -
21 -DHCP Administrator Enable/disable dynamic IP addressing
22 -
23 -IPAddress Administrator Set IP address
24 -
25 -IPCONFIG Operator Display/Configure IP Settings
26 -
27 -IPMask Administrator Set IP Subnet Mask.
28 -
29 -IPTable Operator Display IP Table
30 -
31 -DEFRouter Administrator Set default router
32 -
33 -ADDDns Administrator Add an entry to DNS server List
34 -
35 -
36 -ADDMaster Programmer Add a master entry to IP table
37 -
38 -REMMaster Programmer Remove a master entry to IP table
39 -
40 -
41 -ADDSlave  Programmer Add a slave entry to IP table
42 -
43 -REMSlave  Programmer Remove a slave entry to IP table
44 -
45 -
46 -
47 -HELP - Detailed help available. 
48 -
49 -Type a command followed by a space and '?' to see options for that command (i.e. HELP ?)
50 -
51 -HELP ALL will display a list of all commands.
52 -
53 -HELP DEVice will display a list of commands specific to this device.
54 -
55 -HELP ETHERnet will display a list of Ethernet commands.
56 -
57 -HELP FILE will display a list of commands for file operations.
58 -
59 -HELP SYStem will display a list of general system commands.
60 -
61 -HELP RF will display a list of commands for the radio chip if available.
62 -
63 -HELP OSD will display a list of commands for the on-screen-display if available.
64 -
65 -HELP RAVA will display a list of commands for RAVA VOIP if available.
66 -
67 -HELP BACNET will display a list of commands for the BACNET stack if available.
68 -
69 -HELP USER will display a list of commands added to the system by user programs.
70 -
71 -HELP CRESTIMERENG will display a list of commands for the Crestron Timer Engine.
72 -
73 -HELP xxx* will display a list of commands starting with xxx.
74 -
75 -
9 +DEFR 0 x.x.x.1 - to set Default Gateway