Skip to Content

Changes for page ZUM-HUB4 Processor Setup

Last modified by Craig Lewis on 2025/03/13 15:50
From version 22.1
edited by Alexander Mott
on 2022/09/19 17:44
Change comment: There is no comment for this version
To version 25.1
edited by Alexander Mott
on 2023/05/11 15:11
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -38,8 +38,8 @@
38 38  **** Set IP subnet mask: ##ipm 0 (% style="color:darkgoldenrod" %)**255.255.255.0**(%%)##
39 39  **** Set default gateway: ##defr 0 **10.0.0.1**##
40 40  **** Set hostname: ##host HUB4-CPP##
41 -**** If ZUMNET-JBOXs will be connected via the LAN port, set secure gateway: ##securegateway default ##
42 -***** (Note: this setting defines whether or not a secure connection is required on the LAN side of the control processor for Crestron devices)
41 +**** If ZUMNET-JBOXs or other non-secure Crestron devices such as 3-Series EISC will be connected via the LAN port, set secure gateway: ##securegateway default ##
42 +***** Note: this setting defines whether or not a secure connection is required on the LAN side of the control processor for Crestron devices
43 43  **** Reboot the processor: ##reboot##
44 44  *** If connecting lighting hardware to the Control Subnet port, then you may optionally configure the Control Subnet. If manually configuring the control subnet, we recommend the following IP range as it won't conflict with corporate networks:
45 45  **** Using the "Functions>Ethernet Addressing...>Control Subnet" menu of Toolbox:
... ... @@ -55,7 +55,7 @@
55 55  ***1. Be on the building LAN
56 56  ***1*. The ZUM-HUB4 LAN should be configured with a static IP or DHCP reservation
57 57  ***1*. Building network must be configured to allow communication between ZUM-HUB4 and all lighting devices
58 -***1*. This requires: ##securegateway default##
58 +***1*. Run the command: ##securegateway default##
59 59  ***1. Be connected to the Control Subnet port
60 60  ***1*. Control Subnet must be configured correctly (see above)
61 61  ***1*. If lighting devices must be able to communicate with the building LAN, run the command: ##isolatenetworks off##
... ... @@ -72,13 +72,13 @@
72 72  *** Locate the "nvram" folder
73 73  *** Right click the folder and select "Change File Attributes"
74 74  *** Change "Numeric Value" to 777
75 -*** Disconnect from the processor
75 +*** Disconnect from the processor in FileZilla
76 76  ** WinSCP instructions:
77 77  *** Connect to the processor at port 22
78 78  *** Locate the "nvram" folder
79 79  *** Right click the folder and select "Properties"
80 80  *** Change "Octal Value" to 2777
81 -*** Disconnect from the processor
81 +*** Disconnect from the processor WinSCP
82 82  
83 83  = Crestron License Generation =
84 84  
... ... @@ -85,7 +85,9 @@
85 85  * Connect your computer to the same network as the processor. Make sure your computer’s IP settings are compatible with the lighting network and do not conflict with any devices already on the network
86 86  * Connect to the ZUM-HUB4 in Crestron Toolbox
87 87  ** Run the "##ver##" and verify that the reported firmware is v2.7100.00016 or greater
88 -** Navigate to Functions>License Management...>Add License
88 +** Open the Functions>License Management... window
89 +*** If "ZumHubProgramming" license is listed with "Expiration: Never", then the license has already been activated and this step is not necessary
90 +** Navigate to the Functions>License Management...>Add License tab
89 89  ** Open [[Crestron's SW-HUB4-PROG licensing form>>https://app.smartsheet.com/b/form/e06b27d442ba4e668e31ffdf5f6e6322]] in a web browser and generate the license key
90 90  *** The Customer Number and PO# must be provided by the Crestron Agent for the job
91 91  *** The Hostname and System Key can be viewed in Toolbox by navigating to Functions>License Management...>Add License