Skip to Content

Changes for page GLPAC Expansion Setup

Last modified by Alexander Mott on 2023/12/12 00:02
From version 14.1
edited by Alexander Mott
on 2022/06/13 15:09
Change comment: There is no comment for this version
To version 17.1
edited by Alexander Mott
on 2022/06/13 15:53
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -50,9 +50,9 @@
50 50  * Connect to the GLPAC via USB
51 51  * Open Text Console and run the following commands to configure the GLPACs IP settings (example is for a GLPAC at (% style="color:blue" %)**10.0.0.11**(%%) on a **10.0.0.0(% style="color:darkgoldenrod" %)/24(%%)** subnet with hostname (% style="color:purple" %)**GLPAC-1**(%%))
52 52  ** Disable DHCP: ##dhcp off##
53 -** Set IP address: **##ipa 0 (% style="color:blue" %)10.0.0.11(%%)##**
54 -** Set IP subnet mask: **##ipm 0 (% style="color:darkgoldenrod" %)255.255.255.0(%%)##**
55 -** Set default gateway: **##defr 0 10.0.0.1##**
53 +** Set IP address: ##ipa 0 (% style="color:blue" %)**10.0.0.11**(%%)##
54 +** Set IP subnet mask: ##ipm 0 (% style="color:darkgoldenrod" %)**255.255.255.0**(%%)##
55 +** Set default gateway: ##defr 0 **10.0.0.1**##
56 56  ** Set hostname: ##host (% style="color:purple" %)**GLPAC-1**(%%)##
57 57  ** Reboot the GLPAC: ##reboot##
58 58  * All GLPACs on the job will need to be configured in this way, but if the network is not up (i.e., if it is not yet possible to plug in at one location and communicate via Ethernet to all GLPACs on the job) then it is more time efficient to proceed and load the program over USB before moving on to the next GLPAC
... ... @@ -81,9 +81,9 @@
81 81  ** If prompted, click "Yes" to overwrite the device's IP Table
82 82  ** If prompted, click "Yes" to ignore that the program specifies a different model
83 83  * Wait for the GLPAC to finish rebooting and then connect via Text Console
84 -* In Text Console, send the following commands (example is for a processor at (% style="color:orange" %)**10.0.0.10**(%%) and a GLPAC with IP-ID (% style="color:darkgoldenrod" %)**B1**(%%)):
84 +* In Text Console, send the following commands (example is for a processor at (% style="color:orange" %)**10.0.0.10**(%%) and a GLPAC with IP-ID (% style="color:olive" %)**B1**(%%)):
85 85  ** Remove current IP Table entry: ##rems E0 10.44.5.55##
86 -** Update IP Table entry: ##adds (% style="color:darkgoldenrod" %)**B1**(%%) (% style="color:orange" %)**10.0.0.10**(%%) E0##
86 +** Update IP Table entry: ##adds (% style="color:olive" %)**B1**(%%) (% style="color:orange" %)**10.0.0.10**(%%) E0##
87 87  ** Reboot the GLPAC: ##reboot##
88 88  * Wait for the GLPAC to finish rebooting
89 89  * Connect to the processor via Text Console and run the command: ##ipt##