Skip to Content

Changes for page DIN-CENCN-2 Setup

Last modified by Alexander Mott on 2024/02/09 01:01
From version 9.1
edited by Alexander Mott
on 2022/09/17 00:38
Change comment: There is no comment for this version
To version 14.1
edited by Alexander Mott
on 2023/07/10 14:54
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,11 +1,7 @@
1 -{{box title="**CONTENTS**"}}
1 +{{box cssClass="floatinginfobox" title="**CONTENTS**"}}
2 2  {{toc/}}
3 3  {{/box}}
4 4  
5 -(% class="row" %)
6 -(((
7 -= DIN-CENCN-2s in SHOWRUNNER™ =
8 -
9 9  DIN-CENCN-2s are Cresnet-to-Ethernet bridges which convert data over the Cresnet bus into high-speed Ethernet traffic. This helps avoid issues with bandwidth over the Cresnet bus for jobs which have a large number of Cresnet devices, as well as allowing for additional power supplies to provide power Cresnet devices.
10 10  
11 11  For SHOWRUNNER™ installations, the IP address of the DIN-CENCN-2 does not matter as long as it is in the same range as the processor and does not conflict with any other devices on the network. Instead, DIN-CENCN-2s are identified to the processor via their IP-ID. Note that which Cresnet devices are landed at each Net of each DIN-CENCN-2 matters, and if devices are moved between Nets or between DIN-CENCN-2s then the configuration will need to be updated (see below). Chief Integrations typically provides an SRTakeoff.xlsx spreadsheet with an IP Table tab that lists all the DIN-CENCN-2 IP-IDs in the program. If no takeoff is provided, then the processor's IP table can be checked by running the ##ipt -t ##command from the processor after the configuration is loaded. DIN-CENCN-2's will typically have IP-IDs in the "##Dx##" range.
... ... @@ -12,7 +12,7 @@
12 12  
13 13  = IP Configuration =
14 14  
15 -Typically, each DIN-CENCN-2 will need to be initially configured via USB, unless their MAC addresses are already known and the lighting network has a DHCP server (either by running DHCP server software on your computer, or if the processor has a control subnet or is running the [[SHOWRUNNER™ DHCP Server>>doc:SHOWRUNNER™ User Guide & Wiki.Troubleshooting.DHCP Server.WebHome]]).
11 +Typically, each DIN-CENCN-2 will need to be initially configured via USB, unless their MAC addresses are already known and the lighting network has a DHCP server (either by running DHCP server software on your computer, or if the processor has a control subnet or is running the [[ShowRunner™ DHCP Server>>doc:SHOWRUNNER™ Setup Guide.Troubleshooting Guide.Advanced Tools.DHCP Server.WebHome]]).
16 16  
17 17  Whether connected to the DIN-CENCN-2 via USB or Ethernet, the process to configure the static IP addresses is the same:
18 18  
... ... @@ -27,6 +27,14 @@
27 27  ** Reboot the DIN-CENCN-2: ##reboot##
28 28  * Repeat for all DIN-CENCN-2s on the job
29 29  
26 +(% class="wikigeneratedid" %)
27 += Useful Commands =
28 +
29 +Below is a list of useful commands that can be used with DIN-CENCN-2 to help with troubleshooting Cresnet issues.
30 +
31 +* ##ppndiscover## - this command scans each of the DIN-CENCN-2's Nets and prints out a list of connected Cresnet devices identified by their connection ID and their TSID
32 +* ##cnettest## - this command scans each Net and prints a summary of the number of devices on each net as well as any Cresnet issues found (e.g., "Y short to Z" or "Power Fault")
33 +
30 30  = Moving Cresnet Devices =
31 31  
32 32  In SHOWRUNNER™, which Net each Cresnet cable is landed on is important. Each DIN-CENCN-2 is firmware limited to a maximum of 25 Cresnet devices per Net, and which CENCN-2/Net each device is on is tracked in the configuration file. If devices are moved between DIN-CENCN-2s or moved between Nets on the same DIN-CENCN-2, then the configuration file must be updated. Every device in the configuration has a ##"DeviceHostId"## (the host DIN-CENCN-2's IP-ID) and a ##"DeviceHostBranch"## (the Net of the DIN-CENCN-2) associated with it.
... ... @@ -37,4 +37,3 @@
37 37  1. Cresnet IDs must be in the hexadecimal range 03 to 1B
38 38  1. Any children devices (such as NS occ sensors, photocells, GLPPA-KP keypads, etc.) must also be moved. If the parent Cresnet ID is changed then the children IDs must also be updated
39 39  1. If devices are moved from a DIN-CENCN-2 to be landed directly on a processor (or landed on a DIN-HUB on a processor), then the device host ID should be ##null## and the host branch should be ##0##
40 -)))