Skip to Content

Changes for page DIN-CENCN-2 Setup

Last modified by Alexander Mott on 2024/02/09 01:01
From version 6.1
edited by Alexander Mott
on 2022/09/16 20:54
Change comment: There is no comment for this version
To version 5.3
edited by Alexander Mott
on 2022/06/17 19:42
Change comment: Update document after refactoring.

Summary

Details

Page properties
Parent
... ... @@ -1,1 +1,1 @@
1 -SHOWRUNNER™ Setup Guide.SHOWRUNNER™ Installation Guide.SHOWRUNNER™ Installation and Network Setup.WebHome
1 +SHOWRUNNER™ Setup Guide.SHOWRUNNER™ Installation Guide.WebHome
Content
... ... @@ -1,16 +1,10 @@
1 -{{box title="**Contents**"}}
2 -{{toc/}}
3 -{{/box}}
1 +=== DIN-CENCN-2s in SHOWRUNNER™ ===
4 4  
5 -(% class="row" %)
6 -(((
7 -= DIN-CENCN-2s in SHOWRUNNER™ =
8 -
9 9  DIN-CENCN-2s are Cresnet-to-Ethernet bridges which convert data over the Cresnet bus into high-speed Ethernet traffic. This helps avoid issues with bandwidth over the Cresnet bus for jobs which have a large number of Cresnet devices, as well as allowing for additional power supplies to provide power Cresnet devices.
10 10  
11 11  For SHOWRUNNER™ installations, the IP address of the DIN-CENCN-2 does not matter as long as it is in the same range as the processor and does not conflict with any other devices on the network. Instead, DIN-CENCN-2s are identified to the processor via their IP-ID. Note that which Cresnet devices are landed at each Net of each DIN-CENCN-2 matters, and if devices are moved between Nets or between DIN-CENCN-2s then the configuration will need to be updated (see below). Chief Integrations typically provides an SRTakeoff.xlsx spreadsheet with an IP Table tab that lists all the DIN-CENCN-2 IP-IDs in the program. If no takeoff is provided, then the processor's IP table can be checked by running the ##ipt -t ##command from the processor after the configuration is loaded. DIN-CENCN-2's will typically have IP-IDs in the "##Dx##" range.
12 12  
13 -= IP Configuration =
7 +=== IP Configuration ===
14 14  
15 15  Typically, each DIN-CENCN-2 will need to be initially configured via USB, unless their MAC addresses are already known and the lighting network has a DHCP server (either by running DHCP server software on your computer, or if the processor has a control subnet or is running the [[SHOWRUNNER™ DHCP Server>>doc:SHOWRUNNER™ User Guide & Wiki.Troubleshooting.DHCP Server.WebHome]]).
16 16  
... ... @@ -27,7 +27,7 @@
27 27  ** Reboot the DIN-CENCN-2: ##reboot##
28 28  * Repeat for all DIN-CENCN-2s on the job
29 29  
30 -= Moving Cresnet Devices =
24 +=== Moving Cresnet Devices ===
31 31  
32 32  In SHOWRUNNER™, which Net each Cresnet cable is landed on is important. Each DIN-CENCN-2 is firmware limited to a maximum of 25 Cresnet devices per Net, and which CENCN-2/Net each device is on is tracked in the configuration file. If devices are moved between DIN-CENCN-2s or moved between Nets on the same DIN-CENCN-2, then the configuration file must be updated. Every device in the configuration has a ##"DeviceHostId"## (the host DIN-CENCN-2's IP-ID) and a ##"DeviceHostBranch"## (the Net of the DIN-CENCN-2) associated with it.
33 33